Models > C201-C > Instructions

C201-C Jenn-Air Cooktop - Instructions

All Instructions for the C201-C
91 - 105 of 239
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Rear burner always high, ignored temperature setting.
Turned off breaker for range. Removed 4 phillips screws on control panel, tipped it forward and rested it on top of partially open oven door. Removed knob and nut on old switch. Moved wires, one at a time from old to new switch. Put new switch in place, tightened nut and pushed on knob. Put control panel back in place and installed 4 screws... piece of cake.
Parts Used:
Surface Unit Infinite Switch Kit
  • Dana from Chapel Hill, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
parts needed to be replaced
Hubby & I
Parts Used:
Surface Burner Knob Kit
  • Phyllis from MAPLE VALLEY, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace burnt out indicator light
I feel that the design of the indicator light, with the base attached to the bottom of the lens, is ingenious in that it eliminates the need for fasteners in that confined space, However, the plastic used for the base needs to be more flexible. Part of the base broke off in trying to force the base over the bottom of the lens. Fortunately, there was enough left on the base that I could slip it over the bottom of the lens and complete the installation.
Parts Used:
Indicator Light Kit
  • Melanie from SALIDA, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip bowl rusted out
pulled the old one, inserted the new one.
Parts Used:
Chrome Trim Ring - 8 Inch Drip Bowl - Chrome - 8 Inch
  • William from TULSA, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner receptacle failed (stove over 30 years old)
Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.
Parts Used:
Surface Burner Receptacle Kit
  • BETH from COUNCE, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right front burner switch burnt out
Shut off power. Removed screws holding panel.Removed wires from old switch.Installed wires on new switch and reinstalled panel.EASY
Parts Used:
Infinite Switch
  • FRANCIS from MILLBURY, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The radiant ring element had broken
Removed old element, plugged in new one, tested ok
Parts Used:
Delta Frame Surface Unit - 8 Inch
  • Martin from Alexandria, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change the Oil/Grease Filter
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.
Parts Used:
Grease Filter
  • Yong from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Elec. stove-top knobs (imprinted with HI to LO numbers 1 to 10)worn to non-readable.
Knobs sent fit the shafts, but due to molded internal stop wouldn't seat. Had to drill out the stop, and also file down the shafts a bit for knobs to seat acceptably closer to stove-top.
Parts Used:
Surface Burner Knob
  • Lenice from Stuart, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken knob dhaft
Replaced wires from broken to new part.
Parts Used:
Surface Unit Infinite Switch Kit
  • Richard from THE WOODLANDS, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
stove top burner would not heat
new element plugged into burner connection- an easy fix
Parts Used:
Delta Frame Surface Unit - 6 Inch
  • Marjorie from Indianapolis, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My electric range burner was not heating.
All I had to do was remove the old burner and push the new burner into place. It couldn't have been easier.
Parts Used:
Delta Frame Surface Unit - 8 Inch
  • Joyce from Oceanside, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Could Not Use One Burner
Turned power to stove off. Removed two screws from cover - lifted cover up and pulled switch out and disconnected wires. Put new switch in and connected wires. Made sure that it was in correct position by placing knob on to make sure off position was correct - then placed plate in position and closed - put two screws back on plate and put new knob on. Turned power back on and turned knob and burner back in operation
Parts Used:
Surface Burner Knob Surface Unit Infinite Switch Kit
  • Anne from Bedford Hills,, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lost one of the knobs
Ordering and installing was easy. The hardest part was getting the exact match to 20 yr. old appliance knobs. First one I ordered had wrong shaft hole, but it matched perfectly in design. Decided to reorder and just replace all four with matching new-style knobs and the correct shaft hole. Yeah. Looks great and REALLY easy to install.
Parts Used:
Surface Burner Knob
  • Sabra from Dallas, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
center piece of the heating element broke off
so easy, just ordered the part, the part came and inserted the element into the stovetop
Parts Used:
Delta Frame Surface Unit - 6 Inch
  • Elaine from Atascadero, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the C201-C
91 - 105 of 239
Back to Top