BDNS24L9K (BN91D) Admiral Refrigerator - Instructions

I watched the video on how to change the ice maker, very easily explained, and removed the old in about 10 minutes.After seeing how the old one came out it only took five minutes to install the new one. The appliance repaircompany wanted$120 just to diagnose the problem,i bought the part from partselect for$104 total. This is the forth time I've used this site and saved a ton of money.

pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip the insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.

Disconnected power--removed ice holder tray--removed ice maker end cap--disconnected electrical wires--removed one screw holding ice maker to refrigerator--lifted up on ice maker to remove it from two holders--took control wire from old icemaker and installed it on new one--reinstalled new icemaker in reverse order.

Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Since I had more than one issue, I decided to replace the entire ice maker. All I needed was a nut driver and it took 5 minutes. Three hex screws and unplug the wire harness and the whole unit came out. I changed the harness over and installed the new unit. I left for work and came home to ICE. It was Great!!!

1. Viewed the video furnished (very helpful) 2. Turned off circuit breaker (avoids having to move the refrigerator), took my chances and left the water on 3. Removed the ice bin 4. Removed bottom retention screw, loosened the top two screws 5. Lifted the old ice maker free of top two screws 6. Used the bright flashlight to see how to release the rear electrical connection 7. Placed old unit on toweling, removed the electrical harness, the bail and the lower retention offset bracket (needed because the Kenmore's bottom retention is toward the center of the ice maker) and reinstalled them on new unit, taking care to maintain the original harness clip method 8. Carried the new unit to the refrig and installed the rear harness connector, then lifted it to mount on the top screws, forced it down to correct position, installed lower screw and tightened all three. 9. Placed bail in 'Operate' position, Installed bin and turned on the power. 10. Next morning, success!

Once I received the new icemaker, I removed the old one by loosening the two upper screws and removing the lower. The wire connector came out easily. The wire and the bale from the old unit had to be transferred to the new unit. Then the new unit was reinstalled and the wire plugged back in. It took several hours for the cubes to begin dropping.

Ordered the replacement. Removed the old one, followed the instructions, installation was a snap.

The part came in 5 days from time order. take less then 10 minute done. part work well, have ices again, Thank you Part Select. we don't have to buy a new Rerigerator

I started by changing the water inlet valve. It made one batch but it did not eject into the ben. I removed the ice maker and found that the coating inside was bad. I changed out the ice maker and it is now making lots of ice.

Reomove Ice bin from unit.remove plastic front. Remove the 2 bottom screws of dispenser assembly. removed old assembly. position new assembly. Replace bottom 2 screws.reinstall plastic front and reinstall into unit.

I went on line and viewed the video. It looked so easy I ordered the new ice maker. Having the information I was able to take apart the old one and view the problem. By the time the new part arrived I was experienced with the installation. I was shocked when the new ice maker arrived within 1 day. I completed the installation without a hitch, I was delighted with the ease of installation and the operation of the new iace maker.Thanks again...Ray

I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.