Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ATF6000ES1 > Instructions

ATF6000ES1 Frigidaire Washer - Instructions

All installation instructions for ATF6000ES1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF6000ES1
106-120 of 228
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken shock absorber on washing maching

  • Customer: Richard from Novi, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 1 people found this instruction helpful
Watched video on-online when I ordered the parts. The video showed the left side shock replacement and it looked very easy, however; the right side require a little more work due to the motors and electrical box that had to be moved before I could remove the shock pins. I layed the washing machine on its back and removed the broken shocks and put the bottom pins back in on each schock and then stood the machine back up right; took the back panel off so I could replace the upper pins on both sides with ease. I then went to the front and re-attached all the hoses, clamps, and electrical box. Before I replace the front panel, I took a 1/4 socket and wratchet and leveled the machine in its perminent place by adjusting the four feet by reaching into the machine with the 1/4 inch socket and wratchet and adjusting the feet one by one until level.

Shock broke

  • Customer: Robert from Coldwater, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 1 people found this instruction helpful
replaced as instructed.

Bouncing and noisy washer

  • Customer: Chad Trainum from Albuquerque, NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
I had read the instructions and suggestions on the site. The product arrived with a good set of instructions. I used the deep socket to push in the "catch" on the pins. Once the catch is depressed I pulled and twisted a bit to get the pins out. After I pulled both broken shocks out I replaced them as instructed. I did use a long wooden dowel to get the pins all the way in. Read the instructions and follow what they tell you and it'll be done in under 15 min.

knocking noise when washer changed directions

  • Customer: Randy from Okeechobee, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
First I removed two screws in front lower panel to access lower portion of washer machine. Use pilars to push four plastic pins from each end of two vibration/shock abs. Job was very easy and took less than 30 minutes to complete.

the wash tub was loose and making noise and bouncing all over the place

  • Customer: Eve from Davie, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
we removed the back panel of the washing machine, removed the old pins to the shocks and re-installed the shocks and pins. one pin gave us a hard time but it eventually went back in. the job was not to bad to do and now the wash machine is so quiet we can't even tell that it is on : ) this is our second repair that we have done on it ourselves, the first time we had to install a new control unit and spring and that was fairly easy also. who needs to spend alot of money to get their appliances repaired, you can easily do it yourself and save some money, plus we ordered the parts online and received them in about 2 days

The tub had severe vibration and actually impacted the sides of the washer

  • Customer: Paul from Prospect, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
The machine had the vibration for sometime but still worked so we left it alone until it stopped working. After some trouble shooting I discoverd 1. both lower shocks were broken off and the tub had hit the controller connector on the front right side so hard it had come loose. After plugging it back the washer worked again so I ordered the shock absorber kit from part select. I was able to install it by only removing the front lower cover. The pins took some effort to push back in but the parts fit perfectly and we are back in business. I had to use a large set of channel locks to force the pins back in as well as tapping them with a hammer.

Washer off balance caused springs, shocks to break

  • Customer: Lois from Pasadena, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 1 people found this instruction helpful
Took off the front, and put a come along to rafters in garage to lift tub.
Replaced shock asborers, waited for spring kit to be delivered, replacing all.
Still isn't working need to check wiring to some compoments to see if a wire is broken.
Hope to have it washing soon

washer went off balance, barrel in washer was loose

  • Customer: Marcie from Montesano, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Disconnected hoses, unplugged, took off top and back of washer. Removed the white plastic thingys that retained the broken shock absorbers. Installed the new ones, using a hammer and 1/2" copper pipe section to place white plastic thingys. Put back, top on. Reconnected hoses, plugged in. Presto!

Drum would sway out of balance

  • Customer: Jeffrey from Woodinville, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
Followed the kit instructions to the letter. working around tight clearences was really the only thing to slow me down. The other posts tell the rest of the story better than I can.

Broken shock

  • Customer: Scott from Pearland, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 1 people found this instruction helpful
My washer was leaking a bit on the left side, apparently from the place water enters from filler. I spent a bit of time inspecting that side of the thing and my jaw dropped when I finally saw the other side of the washer, the upper shock was broken off and the thing was not connected.

I got my parts fast and removing the pins was a bit troublesome but some from access standpoint, but it wasn't hard - just took some extra effort and prying from the head side. Seems to run better with new shocks and no more leaking so far.

broken shock absorbers (were all plastic)

  • Customer: Patrick D from Port Orchard, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
It took more time to remove the screws on the back panel..
remove back panel for better access..
remove speed access box on lower left side ( 2 screws) to get access to nylon pegs, squeeze down on tabs and pull out . the little tabs are on the oppsite side of the split nylon...
Replace shocks and nylon pegs..
reattach speed access box.
put the back on.....
easy job, the new shocks are part metal, make sure the metal side of shocks go towards the tub...

both left and right shock absorbers had broken into they are plastic on my front load galeriey series washer

  • Customer: Les from Belleview, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the bottom front panel ( 2 screws) and about 8- 10 inches back were the shock absorbers...the one on the left was easiest nothing in way I squeezed the locking tab and pushed the pin thru to remove the shock absorber...on the right side was a little tricky but got my arm round the drain hose and small pump and pushed that pin thru as well...installed new shocks and was good to go...I did call a local repair business here in belleview florida was told the shocks themselves would cost 37.00 for the pair and about 150 - 175 in labor...I paid 22.00 from parts select and did my own labor thanks for all the help...les

Broken shock - slight leak

  • Customer: Duffy from Wheaton, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
You could do the replacement by just removing the maintenance panel on the front, but removing the rear panel gives you more options for getting at the shocks.

The front panel comes off with 2 screws, the back has a lot of screws holding it on, a cordless drill is the way to go.

Prying on the head of the plastic bolt with a pair of needle-nosed pliers while pushing down on the tab seemed to work well. I did have to remove a small box that houses electronics to remove the one from the right side.

While I was in there, I tightened up the numerous bolts that holds the drum shell together. Machine is much smoother now and no leaks.

washing machine made loud clunking noise and wouldnt spin on high speed

  • Customer: JEFF from COLONIE, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
First I unplugged. The machine from the outlet then disconnected the two water supply lines from the machine. Next I removed the back panel to gain access to the bottom of the drum. Next I took a nut driver and used it to depress the little tab on the push pin that hold the bottom part of the strut on. After getting the pins out I replaced the old strut assembly withe the new one. I used the nut driver again. But this time I used it as a set tool. Place the nut driver on the end of the push pin and gently tap with a hammer. Until the pin is all the way in. After that I reversed the assembly process to put the machine back together.

The door on the washer would not lock, therefore, you could not wash clothes.

  • Customer: Sarah from Greensboro, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
After some research online about my Frigidaire Washer, I pre-determined that the problem could likely be the lock mechanism. I ordered the part and it arrived within 3 business days. My son removed the screws from the back of the washer, slid the top off and removed the old part and replaced it with the new part. It took about 20 mins. The machine is now working properly again. The door catch that I ordered did not work with the door lock I ordered. However, the old door catch that was still in good working order does work with the new door lock and switch assembly that I purchased.
All Instructions for the ATF6000ES1
106-120 of 228