Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ATF6000ES1 > Instructions

ATF6000ES1 Frigidaire Washer - Instructions

All installation instructions for ATF6000ES1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF6000ES1
76-90 of 228
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

One shock was broken

  • Customer: Larry from Alamo, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
I removed the front access cover and the rear cover. It was also necessary to remove the water level sensor (attached to the tub drain hose) to access one of the shocks. Not having a 1/2" deep socket, I used a 2" piece of 1/2" copper pipe to depress the locking tab on the shock attachment pins--worked great. Pulled the pins out with pliers. Putting the pins back in after replacing the shocks was easiest to do using 'channel-lock' pliers to grab the bracket and the pin head and squeeze in the pin. The only problem was that my copper pipe piece fell into the drain hose when removing one of the pins! Had to take the drain hose loose to fish it out.

broken shock

  • Customer: John from Glennallen, AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
removed front panel and used deep socket to remove pins that hold shocks. front left shock took most of the time because of hoses and a unit in the back that needed to be released to be able to remove the pin on the bottom. the right shock was a piece of cake to replace. used a hammer to pull the pins into place (i did not use it to tap on them ) . lots of bloddy fingers from sharp edges.

Washer was "clunking" when in use

  • Customer: Mike from Central Square, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
I replaced both shocks, as both shocks were broken! Keep in mind that Parts select packages them in pairs. I order 2 packages or 4 shocks, guess I have another pair for ~ 5 years from now. These are located under the front bottom panel, so no need to isolate water lines or even pull this sucker away from the wall. Tight clearances are the only factor from making this really easy. Use some Vaseline to assist inserting the new plastic pins.

Noisey shock absorber

  • Customer: Ed from Clackamas, OR
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
The parts came with instructions They stated to remove the front panel. This only gets to one side for a difficult repair. I removed the back panel then it was a snap. Easiest with two people.

washer would not got to high speed spin

  • Customer: scott from Toledo, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 16 people found this instruction helpful
well i took the dryer off the top took, the 6 screws out that keep the top then took the soap tray out super easy then there was like 5 screws that keep the controls of the washer because the control board is behind it then just did on wire plug at a time the wires are long enuff thank god you do have to move some light things just some clear things but is so super easy the thing that the knob goes on is kind hard to get off but I just pushed it out from the back and thats it done less than 15 min and i took the dryer off the top and put it back on alone super easy anyone could do it cakes and pies

shocks broke away from washer drum

  • Customer: Rita from Cambridge, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 1 of 1 people found this instruction helpful
replaced the two shocks with the new ones by removing the pins that held the old ones in place.

dryer would not spin

  • Customer: Robb from North Huntingdon, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 1 of 1 people found this instruction helpful
Removed old shock abs. (both sides). The one side, I had to remove the speed control board to access the lower nut on the one shock. Install was fairly easy however, it did not fix the washer. Apparently there was something else (either a switch, the control board or the motor) needs replaced too.

Washer gave error code 31

  • Customer: Tyran from Montclair, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 14 people found this instruction helpful
I opening that top from the rear and saw the same part order plugged in then new part attached it properly and then was done.

broken shock heads-up!

  • Customer: James from Almond, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 1 of 2 people found this instruction helpful
If you have a broken shock (or two) there's a strong possibility that the failure caused, or was caused by, a failure of the "spider" that attaches the inner drum to the "drive shaft". If this is the case, the problem is likely terminal for your washer... unless you purchased a rip-off service contract. The parts will cost upwards of $250 and the bearings and seals that must be dealt with cry-out for a service tech and the associated labor cost. Between the poor engineering and lousy service, I will no longer be purchasing Sears appliances. I did *not* get my money's worth from this washer and Sears has not made good.

$500 Repair for $25, well worth the struggle!

  • Customer: beverly from Miami, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench (Adjustable)
  • 1 of 2 people found this instruction helpful
I replaced both shock absorbers that hold the drum on a front loading washer. They both snapped at the base and have since been replaced by a different style shock absorber. There are 2 pins that hold each part in place. I took 5 minutes to replace 3 pins and about an hour to replace the last one, which was in a very tight spot. After much sweating and swearing, I managed to get the pin back in. Was it worth it? ABSOLUTELY! Partsselect.com is a dream for straightforward repairs. This is the second repair I have done on this machine (which is less than 5 years old) and both repairs have cost less than $30.

Drum was banging around when spooling up and slowing down

  • Customer: Matthew from Pullman, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
The front lower access panel pops off with two Philips head screws. From there, the white pins holding the hold broken shock absorbers can be removed by pressing their locking tab down and pushing them free of the bushing.

After pulling the old, broken items out, the new ones are reinstalled the same way: place the metal end towards the drum, push the white pin through the bushing (only one way is correct) and you're almost done. Reinstall the front panel and get back to having a quiet washing machine!

Broken Washer Drum Vane

  • Customer: KAS from LYNNWOOD, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I follow the instruction that comes with the part. The only thing different is I use wd-40 , to slide the vane better.

Bouncing washing machine

  • Customer: anthony from Florence, AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 1 of 2 people found this instruction helpful
The instructions that came with the new shock absorbers were very detailed and walked me through the repair step by step. The new shock absorbers are much better quality than the old tube style shocks.

worn out vibration/shock absorbers

  • Customer: W R from Venice, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers
  • 2 of 3 people found this instruction helpful
"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be disconnected to get access to the top pin. If I had to do this again it would take about an hour.

Washer would spin in any cycle

  • Customer: Cheryl from Brandon, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Tilted the washer back to take the 2 screws off the bottom to remove bottom plate. Took the 2 nut screws from the bottom of the face plate so that the front of the washer would pull slightly out from the bottom. Removed the 2 screws from the door stricker plate which allowed the door lock assembly to come out through the side of the washer. Unplugged 3 plugs, plugged the new switch in and slid it back into place, put the 2 screws back in to hold it. Reattached the front and the bottom plate. And bingo done. It worked and saved us about $245.00. Very happy!!!
All Instructions for the ATF6000ES1
76-90 of 228