ASD2522VRW00 Amana Refrigerator - Instructions

Unplug, then on the freezer side, remove the drawers, then remove the screws holding the sheet metal cover, remove the rails (for the drawer) that interfere with removing the sheet metal cover. pull the wires off the motor. There is a big plastic piece that holds a small plastic piece that holds the motor. Remove the plastic piece that holds the motor/fan (you might be able to swap the motor by removing the little plastic piece that holds the motor, or you can remove the bigger piece and then remove the small piece that holds the motor). Pull the fan blade off (to reuse), swap the motor. NOTE - the new motor wire terminals may be on the opposite side of the motor vs. the old motor - that is not a problem - there is plenty of room for the wires. After the motor is installed put the fan blade back on, reinstall the removed plastic pieces in the back of the refrigerator. Now, I'd suggest a quick test. Make sure the new motor works and the fan blows before you button it up. Once you know it works, power it off, and put the sheet metal cover back on, reinstall the basket brackets, put the baskets back in place, close the door, and turn it back on.

filter has to be removed and attached then inserted into rifrigerator

just used my hands and popped the old out and just popped the new one in,to easy,thanks barry

Whirlpool SbyS refrigerator ED5FHEXNS02 . I had two problems with the freezer. The drain at the bottom of the freezer kept freezing, eventually leading to water running out the bottom; evap fin kept freezing up as well. The ice maker chute kept freezing up resulting in no ice being made. The online QA was very helpful. I ordered both a Water Inlet Valve and Bi-Metal Defrost Thermostat. Both a cinch to install if you have some basic mechanical skills. The instruction videos was all you need. I was able to guess what the connector was for that came with the Water Inlet Valve kit, but you may want to add an explanation as to what that is for. Since the repairs were only made in the last 2 weeks only time will tell if the problems are fixed. I’ve ordered over the years from PartSelect and always the first place to go.

JUST POP the front panel off and removed the items

Slid the broken one out and slid the new one in.

Just opened the package and drop into tray frame

Purchased a new line, watched the video. The video was a bit misleading the filter housing does not slide out the front to access the removal of the line. I doing so I broke the clip holding the smaller line had to order the complete housing. 90 dollars it's repaired now so all is well .

I started by using some superglue to reattach the broken mounting ring for the pin above the ice door flap. Wait a few minutes for the glue to set (I waited about 2 hours.) After that, install the pin and spring with the spring legs facing the door flap mount and the arch on top. Angle it so the freezer door apply pressure to the spring arch then slot the pin into the circular mount you just glued on the left and the retaining slot on the right.

I watched the recommended you tube video multiple times. I made sure to have the tools and towels ready. I shut off the water supply line, and capped it, removed the backing, and inspected the back. By following the video, the rest was easy. I recommend removing any built up dust and dirt while you have the front apart.

pop out old- insert new

Watched the video...easy!

Once the part arrived it would have been an extremely simple install, however the part was shipped defective. Only 1 of the six potential mounting holes had been tapped. Leaving 5 without threading whatsoever. After demanding a refund I was told I would have to pay for shipping again to send it back and it would talk 7 to 20 weeks ........ yes you read that correctly. For my return to be processed and I could be issued my refund. Long story short I tapped the holes myself and was then able to install. Everything works but I will never buy ANYTHING from this website again.

Unplug fridge, turn off water to fridge
Uninstall ice maker (some tools needed)
Remove ice buildup inside water line

Purchase new ice maker and installed it while watching a youtube video of how to do it. Once installed, turned on the water line and plugged in fridge.

Bought new one and installed