ASD2123DRW Admiral Refrigerator - Instructions

The replacement went very well. Fast shipping, I watched the Video online and followed the simple instructions. Was done in 10 minutes

Took out socket, replaced new bulb in new socket and plugged in. Easy!

I unplugged the refrigerator. Then removed the ice tray. Then removed the screw holding the ice maker secure. I had a little difficulty lifting the ice maker off the clips on the side of the refrigerator but was successful. Then unplugged the wire harness from the back of the refrigerator an lifted the unit out. Removed the wiring harness from the old unit and installed it on the new one. Then positioned the new unit so I could plug the harness in the refrigerator and lined up the clips to attach it on the side of the refrigerator, being careful to line up the water distribution tube. Replaced the screw to secure the ice maker and plugged the refrigerator back in and it is working very well. I am very hsappy with the repair

Video was helpful and reading the other responses online was a big help also. Followed all of those instructions. Most difficult part was disconnecting the electrical plug to the ice maker. Need a screwdrive or other pointed object to depress plastic tab. Other than that, things went smoothly. HOWEVER, after turning water back on and plugging in fridge, I thought everthing was perfect...no leaks initially. BUT, came back a few hours later to find no ice cubes in the holding tray, "iceburg" formations and ice dams built up again thoughout the freezer. Water was leaking continuously from the ice maker. Upon further analysis, it appears the electronic mechanism keeps telling the fridge to send water to the ice maker...or, it is sending too much before shutting the water off. The tray is overflowing and that seems to be the problem. I'm back to square one, but with a new ice maker.

Quickly after video

i was having to completely empty the freezer about every 4 days and take the back cover off and use a blow dryer (with appliance the powered off) to remove the ice buildup. once the ice is gone, the heater coil is easily removed with a small wire clip. i measured the coil with my voltmeter and it was 220k or so, no open as i expected. the new part gave me a different reading but only about 10k difference. i decided to install the part and see. well, it's been 2 weeks now and the fridge is ice cold and working great again! saved a bundle by doing it myself and the stress of losing food in the fridge - thanks parts select!

We purchased 3 parts, in order of probable part that was broken. Website indicates that the Ice Maker Assembly was 75% likely the problem and indeed it was. Didn't need to install the other 2 parts. It wasn't too difficult to replace. Thanks for the advise, it was right on!

Changed bulb, not the problem, had to remove switch to identify correct choice to order (3 pronged verus 2) after that it was easy beyond having to stand on my head to make the exchange. (N B before removing old switch it actually came back to life)

I'm a 65 year old widow on a limited SS income, so I needed to get my refrigerator fixed as cheaply as possible. Partselect's troubleshooting guides took me right to the problem. I ordered the part on a Friday and it arrived the next Tuesday. It probably took me a little longer than it would a repairman, but I did it myself with just a screwdriver and a nut driver and it only cost me $45 instead of the $200 plus it costs my daughter to have someone else replace hers two years ago. Always remember to unplug amy electrical device before removing the covers or attempting any repair. All I had to do was remove the lower back cover on the refrigerator and, using the partselect diagram, locate the casing that covered the start relay and the overload switch on the left side of the compressor. I popped the casing off with the screwdriver, pulled the relay off (it's sits on two prongs), and remove the red terminal wire from the relay. Installation of the new relay is the reverse steps of the removal. Thanks, Partselect! I will be doing business with you again if the need ever arises.

Watched the video on the web site and then followed the instructions. It was very easy to change. After changing it, I filled it with water from a cup to get it started making ice since the video does not address how to do this. It has been working well ever since. If you are handy with tools, you can do this.

I put in a new ice maker because it was not in very good condition. The water valve had a very slow leak which allowed water to freeze on the way to the ice maker and plugged the line. This problem was in one of your repair articles all of which were very welcome

I had to replace the whole unit. The tray should have lasted longer and there should have been a replacement tray available.The installation was easy. 3 screws removed, unplug unit, turn off water and put in new unit.

After receiving the parts to repair the ice door, I replaced the solenoid and new chute door without problem. Then a problem I had been experiencing for well over a year, re-emerged. No Ice! I realized the icemaker was old, over 12 years and that the Teflon within the wells as well as the contacts for the timer were well worn. The ease of finding parts and the instructions provided by PartSelect, (written, video and users), I would attempt the replacement of the Ice Maker. When I examined the Freezer, I also identified that the Ice Maker shelf and enclosure (where the auger that drives the ice) was broken and barely hanging in place. I quickly identified the additional parts and ordered them. The total repair took about 60 minutes. and was treated to the sound of ice dropping into the bin by early evening. I am very pleased with the service, the quality of the products and the helpful hints from fellow users. I have added PartSelect to my IE favorites and it will be my first stop when I need repairs for any of my appliances.

I wasn't sure about the part I needed so I called the service number, they help me decide on the correct parts for my unit. This was the easiest repair I've ever done. One hex head screw and one clip in electrical connection and we were done. It took less than 5 minutes and now it works like new, no more leaking water and plenty of ice.

Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.