ALE565SAW (PALE565SAW) Amana Dryer - Instructions

Before tearing down unit the video on this site is very usefull. After removing tub noticed cylinder glides were worn out and tub had been rubbing glide bracket. Checked rollers on rear of tub and they seemed fine. The belt tension roller seemed stiff. One glide bracket was worn nearly thru. Replaced tension roller, glides and one glide bracket. Since I had unit pulled down replaced belt. Cleaned unit out good, re-assembled and wife happy. If you had tools and parts in hand you could do job in an hour.

Hardest part was getting the dryer apart. mine was held together by two snap in clips on the top front pryed those up with a flat head screwdriver then 4 hex head screws and i was in. i watched a couple of YouTube videos of different types of dryer repairs. i am not a mechanic by any means but i would say the repair was very easy. parts were shipped fast so i was up and running quickly and for a lot less money. plus i earned alt of browned points with the wife.

Researched the common problem with "dryer not turning on", and tested the top three problems. Removed the dryer front casing and door, unbolted front dryer plate. Used a volt meter on two of the temp gauges, which were fine. Removed the upper back plate of the dryer to the wiring for the knobs and buttons. Used the volt meter on the dryer start button, which was also fine. Went back around to the front and removed the door switch. Tested it with the volt meter and bingo. Replaced that part, dryer works like normal.

Parts came quickly and were correct. Installation was easy after watching video. Made the dryer a little quieter found that it is the motor that is the main source of the noise.

I wook with tools on my job so I thought I might be able to complete this repair. I viewed the repair video on Partselect's web site and dicided to "GO FOR IT" (after all the dryer was already broke). The dryer noise had to be a moving part so I ordered two drum support rollers, one idler pulley wheel and one belt. If I was going to open the unit up I decided I would not leave an old moving part only to have trouble later. The total parts were less then fifty dollars, so if this did not fix it I would not be out a bundle that could have been applied on a new unit. I was not willing to invest more in the aging unit (ex: motor). The parts arrived in less then three working days. The dryer in the video was a differnt model then mine so I had difficulty removing the front. After the actual repairs got started I had it back together in about two hours. I believe one of the Drum support rollers was the problem I could not reproduce the noise by hand during repairs so I was not sure that was the problem. But one of the drum rollors was not turning as free as the other and niether of them turned as well as the new ones. I marked the wires as instructed in the video for easy replacement. My repair time maybe longer then most as I did this repair on my own. After restoring the power and pushing the start button the noise was gone :) making the dryer a much quieter unit. Brian H., Illinois

Lived with operating the dryer by helping spin the drum and then closing the door quick for a couple weeks. Replaced the roller, etc, but when that didn't do it, I ordered the motor. The motor replacement wasn't too tricky. The tricky part was that I initially tried to replace it in the dryer to save time or effort. Take everything apart that comes apart, including the vent fan attached to the motor. Get the motor on the floor in front of you, snap it in place and put it all back together. Not too difficult.

We replaced the Drum Rollers, Belt and Glides the first weekend. This DID NOT stop the noise(very loud squealing noise). I decided it had to be the Idler. Instead of replacing just the Wheel, I replaced the whole unit. Took the front of the Dryer off again, took out the Tumbler, removed the 2 screws on the motor assembly tray, moved it a couple inches forward to gain access to the Idler. R&R the Idler( a little contortion for the arms and wrists, but not horrible) and put it all back to together. Works perfectly and ZERO NOISE. YOU CAN DO THIS. Just be patient and give yourself an hour to save $180.00!!!

My dryer was making some awful noises. First thought was the belt. Eventually isolated it to the wheel on the idler lever. I had the driver taken apart and could cause the noise by turning the wheel by hand. I decided to replace the support rollers and drum glides at the same time. I highly recommend watching the installation video. I can't tell you how much it helped to see the repair done. Especially the magic incantation on how to open up the dryer to make the repair. For me the most difficult part was getting the new belt on during re-assembly. There is very little room to work underneath the drum to connect the belt to the idler pully and motor. I was successful in connecting those first and then working it around the drum second.

Pretty much followed the instructions on the video on the website, very helpful! My model takes 2 rollers, and 2the glides, it wasn't obvious when I ordered the parts that I needed 2 of them. However I installed 1 new roller and 1 new Glide as well as the new belt and the tensioner pulley. Definitely take time to clean out the inside of the dryer it will be very dirty if you have never cleaned it before. Also remember to grease any new rollers. dryer was quiet and ran perfectly after this install.

Removed panels and kept screws together. Removed Multi-Rib Belt and carefully lifted tumbler out. This exposed idler pulley wheel and drum support roller. Removed and replaced New Idler pulley wheel and New drum support roller. Carefully inserted Tumbler and installed New Multi Rib Belt. Manually turned tumbler a couple of times to confirm tension. Pluged in for test and wallop! Purrrs like a kitten.

I removed the toe panel,removed bottom screws from front main panel,removed vent housing,removed main front[outer],removed the screws from top[each side,front],raise top up[hook string to coner of top and tieded it up],removed front panel[4 screws]"front of tub runs on",undo old belt from iddler pulley,removed drum and old belt,removed 2 screws that holds motor assy and removed motor assy,replaced old iddler and pulley,relaced drum glides with new ones,replace tub rollers.Reinstall motor assy, tub, belt, fronts,ck out sound like a new dryer. While I was fixing the iddler pulley I replace all main parts,never was change sence new. Sence I was a retired tec from SEARS and age 74 it was tiring for me,wouldn't been if I was younger.....

i took the front off the dryer took belt loose took the tub out the plastic nut on the blower wheel striped out so i took the blower housing apart along with the motor got vise grips on blower wheel replaced motor blower wheel belt and belt tenchinor and spring cleaned all the lint put it back together works fine

noticed that male half was in good working order, so I just snapped in the new female half; without any tools. easy repair!

Ordered new lint filter from part select; paid for it with credit card on line; waited for delivery in one week; received by ups; unboxed; cleaned filter trap area with vacume; and dropped in new filter.

removed screws from front of dryer,lower bottom [2]removed screws from top panel at bottom [2]removed screws from top front [2]raised top cover. removed drum ,slipped belt off drum.replaced roller and belt.drum turning hard has made motor overheat and stop. i need a motor will order from parts select. good price fastest shipping.