AFI2538AEW Amana Refrigerator - Instructions

I removed the cover panel. There is a clip that holds the relay and capacitor to the pump. Use a screwdriver to pry it off. Unplug the relay. The capacitor is plugged into the relay and they come together which was a surprise, I thought I only ordered the relay. Unplug a cable from the relay. Insert that cable into the new relay and plug it into the compressor. Reattach the clip. One be important instruction. Unplug the refrigerator for at least 8 hours before installation to allow the compressor to cool down. I tried first without allowing the compressor to cool and it did not work. After letting it cool I tried again and it worked like charm. Make sure the refrigerator is unplugged when doing the repair

Remove the shelves and the other trays. Use the nutdriver to extract the screws and the panel. Pay attention to the orientation of plastic parts when replacing plastic slides to avoid breaking the plastic slide components. Avoiding too much stress on plastic parts is important.

Remove the pantry drawer door, then remove the pantry drawer. Remove the 2 vegetable bins to gain rom to see and to ease access. Remove the 2 screws holding the end cap to the interior of the box. remove the slide from the end cap and place it on the new one. Reinstall the end cap being sure to have the tabs go into the slots at the back. Make sure the end cap also mates with the tab in the front, Reinstall the drawer and the bins and the pantry door.

I removed all drawers (including the two above the repair site, removed the left side end cap - it was help in place with only two screws (one screw hole appears never to have had a screw). Swapped out the broken part for the new one, reinstalled the screws, put the drawers back, mounted the operable door to the two hinge pins, and things were fixed.

Ordered parts on Tuesday. They arrived on Thursday and I completed the protect SAP.No Problem at all.I used hints from others,removed the 3 screws with my nut driver and completed the job as a pro.My Bride(of 63 years) was amazed at my ability Thank you Part Select.I informed all of my Family members of your prompt service

I removed salad and veg draws, pantry draw and the two glass shelves. Located and removed the screws holding the pantry side, gently eased the side out and replaced with the new one. Just a breeze to replace and for a 73 old female, pretty good. Thank you PartSelect for speedy delivery of part.

Unscrewed old water filter. Screwed in new filtr. Moved lense off track. unscrewed bulb. Screwed bulb. Slid lense back in.

to repair the center rail, all I did was remove the food and the top glass and insert the rail!!! to repair the end cap all I did was remove the big drawer and remove the broken end cap and replace with the new one. My only thought is this is the third end cap I have had to replace not very sturdy construction where the lid hangs

Remove the vegetable and fruit drawers. Cover of the pantry was off due to the broken pin. Remove the three nuts with a nut driver. Lift up on the old end cap to remove and replace it with the new one. Replace the nuts and put the cover back on. Replace the two drawers and you are done. Repair was easy

Opened the refrigerator door, pulled down the filter cover, twisted the old one out and removed it. Placed the new one in - twisted it into place, replaced the cover and closed the door. It is working great!!

I pulled the frige out, took off the cover from the bottom with a nut driver. Took off the safety clip then pulled the plug out from the relay then the relay came out. Replaced the part and reinstalled the same way. This was really easy and fast.

used the directions from PartSelect

simply repalced

I snapped the cover plate to the filter open. Pulled the filter down and twisted counter clock wise to take filter out. I installed the new filter in by inserting the filter and tuning clock wise to secure the filter. I flushed the water for about two minutes and then allowed it to be put back into service.

My son in law was able to take off the defective end pieces, and replace them with the new ones, in about 20 minutes. 10 minutes were probably spent in finding the right tools.Very easy to do. Parts were received within 2 days of ordering (I placed order on a Sunday).I was able to find the parts right away on your inter net lay out.