AAV7000AJW Admiral Washer - Instructions

When I received the replacement part it did not look exactly the same as the one that came off the washer. After watching the video that was sent with the shipment confirmation I very clearly understood it and was able to do repair in about 10 minutes. It was so easy, I wish that there were more repairs to do to take advantage of your wonderful customer service. You have created a customer for life. Thank you

We went on line and found the correct part. It arrived in 3 days. said it might take 7. Husband and son dismantled the old plastic outer tub that had been slit by the screwdriver. Put the new one in, and filled the tub up with water to check for leaks. When the water got to the level of the fill line, it started leaking. We pumped the water out and stopped to wait for daylight. Next day we lifted the top of the machine and filled it again...the line that goes to the water level knob...was off. The woman found the leak and put the hose back on. We were semi worried when we read the reviews, but in the daylight, it really wasn't all that difficult to change out the broken tub.

Took access panel off of back saw that hose had pulled off of tub, thus the rinse water was just running on floor, re attached hose when the rinse cycle finished and the brake stopped the spin it jerked the hose off once again. It had a spring clamp holding it on, so I reinstalled it with a worm/screw clamp, no problems since. Ordered a new hose to have on hand in case. Jim

you need a ratchet with a socket extension 6" or better to remove the bolt then replace the agitator. The Job is extremely easy.

Simply watched your video, which was very well done, followed step by step and in about 20minutes the washer was successfully repaired. You have a great business model, the the part was easy to order, the shipping was prompt and the video was a plus Steven Hopkins

Disconnect water, power and drain lines. Tip machine on side and remove drive belt. Release 2 clips retaining the top. A putty knife inserted here will do the job. Remove 2 screws holding the front panel and lift straight up to remove. Remove rear access panel and remove hose from the water pump. Be prepared to collect a bit of water when doing so. Disconnect the small hose attached to the drum at left rear. Using vise grips adjusted to grip them TIGHTLY, remove the 6 springs attaching the drum assembly to the machine base. Tip the machine on it,s side (unless you have an assistant) and remove the drum assembly slowly as you make sure the pulley at the bottom clears the bottom hole. With the drum resting upside down loosen but DO NOT REMOVE the 6 screws securing the dish shaped metal plate that holds the snubber in place. I used a 1/4" drive socket wrench with a short extension, a universal adaptor and a 5/16" socket. The snubber will spin freely can be easily removed when these screws are loosened enough. Clean the area thoroughly and then insert the new snubber. Be sure to center the new part carefully and tighten the 6 screws evenly and firmly. Return the drum to the machine and reinstall the 6 springs by again gripping them FIRMLY with vise grips and lifting them up until they slip into their positions. This is the hardest part of the job, take your time and be careful. I elected not to replace these with new ones as mine were not weak or broken. Connect the pump hose and small hose at the back of the drum. Attach the front panel and top. Replace the belt. Reconnect hoses and power cord. Leave small panel off the back until you run the machine and check for leaks. Good job.

opened top using screwdriver to release clips, used socket set to remove two screws holding front panel in place, removed water pump by removing 3 screws and 2 hose clamps, and replaced old pump that had a bad bearing with new water pump -

I unplugged power, then tilted washer back, leaning against wall. I removed the fan belt and manually rotated three things (motor, pump, and transmission). The water pump did not rotate smoothly. I then ordered the watere pump. To install the pump, I simply removed the water supply lines and opened the access panel on the back of the washer. Replacing the pump is as easy as removing 3 bolts and two hoses, installing the new one, and reconnecting. Then reconnect water supply and belt on bottom of the washer.

Don't get unhinged by this easy repair. Easily ordered on line and got the part in two days. The only hard part was the screw was inside up under the washer body and not visible. I had to use an "s" shaped screw driver to take out and put in one screw due to the small work space.

Following the other repair examples posted. Replaced Snubber Ring and 6 tension springs. Washer works great again. No more dancing in the hallway.

Used pliers to remove spring clamps on either end of hose. Removed hose. Put clamps on end of new hose. Slipped hose ends in place and re-secured with clamps. Another save by PartSelect!

Watched videos on how to replace the hose. Armed with the information I started the process. But the videos were wrong. After removing a bunch of screws and not getting to the hose I removed the inspection panel on the rear,three screws and there was the hose.simple. I wished I had not watched the videos.

I remove the necessary panels, hoses and electrical section and removed the tub springs and pulled the tub assembly out of the unit and replace the snubber ring. Was really not hard to do and it worked like a charm. No more problems :)

First thing was to go to PartSelect website to see what others with the same problem did to solve their problem. It was 45% pump and a lot less for the belt. My belt is only a year old so that was out. I ordered my new pump and watched the video on PartSelect a couple of times. I didn't bother to disconnect the water and drain lines. I had my wife hold a plastic 2 quart container under the pump when I pulled the small hose off and didn't spill a drop. Like the man on the video said...the new pump isn't identical but it fits and works fine. Thankx PartSelect!

very easy repair, acess from the back, just a 1/2 dozen screws to change