A190 Maytag Washer - Instructions

Install new siphon break connector: 1. Loosened the clamp holding the drain hose in place on the elbow at the rear of the washer. Removed the hose from the elbow. 2. Removed the round upper access plate on the rear of the washer. 3. Removed the 4 screws holding the elbow in place, thereby releasing the siphon break connector and internal drain hose inside the washer cabinet. 4. Reached through the access port, grasped the siphon break connector end of the internal drain hose, pulled it through the access port. 5. Loosened and removed the clamp on hose, then removed the old siphon break connector from the end of the hose. 6. Installed the new siphon break connector onto the hose, clamped it in place, then returned the hose into the washer cabinet through the access port and positioned it onto the elbow, tightened the part down by reinstalling 4 screws at elbow on rear of the washer and then reconnected/clamped the external drain hose onto the elbow and replaced the access port cover.

Watch the video on how to open this model washer. Unplug the unit. Remove the front panel. remove the bolts so you can lift the top. Disconnect the bleach tube at the top. Lift the top and hold in place with a stick or broom handle. Locate the air gap unit on filler tube. Unscrew the hose clamp on the inlet side of the air gap. Disconnect the hose and pull out the rubber tube. Fold the edges of the rubber valve off the inner nozzle and remove. Install the nozzle into the new Rubber valve. Reverse process to finish.

I hastily (miss diagnosed) the symptoms by assuming that the Drain Pump was in fault, Ordered the Drain Pump part online on Sunday got it early on Wednesday. Installed the Drain Pump but the timer would not move. So back to drawing board. Got on the phone with the nice people on PartSelect ordered the Lid Switch Assembly. Got the part in less than 20 hours To install the Lid Switch assembly remove the back panel by removing 3 sheet metal screws at the top and 2 at the bottom now you will have access to all the wires and the Lid Switch Assembly. It is attached with one sheet metal screw. The hole in the Assembly is slotted so you may have to slide it back and forth for the switch to get activated when you open the door. Installed the part, plugged the washer machine in filled the tank. The washer machine came alive the timer was moving (the washer machine start working again). This washer machine should be good for another 20 years. By the way this was the first breakdown on this washer machine after 20 years of service. Thanks PartSelect for well trained people and prompt service I couldn't have done it with out your help.

I tried to get an appointment with our local appliance repair company, but they cancelled and wouldn't reschedule at a convenient time, so I decided to do it myself. Determined that the Mounting Stem/Tub Seal kit was the needed part and ordered it here. Also had to order the specialty spanner wrench from another website. Parts were delivered in a timely manner. The online video was very helpful and the removal and replacement of the defective part went smoothly. The only problem with the actual repair was with removing the old tub seal gasket -- it took quite a bit of coaxing to get it free. The new parts went in with no problems. However, we have an older model than the one shown in the video -- it has the metal tub top cover with the rubber gasket and ring clamp. This cover is tricky to replace properly. It has to be at just the right height to avoid interference with the spinning inner tub (too low) or with the washer lid (too high). You also have to make sure that the rubber gasket it not twisted or crimped by the ring clamp. It took me three tries to get this just right. After that, everything worked fine and the leak is fixed.

Be very, very careful not to cross thread the filler hose, onto the nylon valve housing. Recommend some lubrication, and a pair of velvet gloves.

remove 2 screws in front at bottom pull front panel up & off, remove 2 bolts from top (underneath both sides) lift top up hose is on left. the replacment part is diffrent so you need to trim the plastic ,on problem.

Removed access panel on back of machine to remove Air Tube where it connects to wash basin. Removed control panel cover on top of machine and front panel of machine so top could be lifted for easier access to the point where Air Tube plugs in to water level selector switch. Tube is attached at both ends via spring clips. Replaced tube; problem solved. As a note, the old tube was clogged, and once cleaned, the machine functioned normally again. I had already ordered the replacement so I installed it in place of the old tube when it arrived. The new tube is significantly longer but functions perfectly.

I got all of my repair information from your website. I started with 'Maytag washer leaks' and found out that, statistically, the rubber injector valve was the first most likely leak source. Then, to check if this was actually the leak, I lifted the top of the machine during the fill cycle, and watched the water spritzing from the housing that enclosed the Rubber Injector Valve. Next, I watched one of your repair videos associated with replacing the valve. Next, I ordered the part from you. When it came, I installed it. The whole process, from beginning to end, was very good.

Removed the old one installed the new one

Replaced the pump. The front panel screws were rusty. I also replaced the belts at the same time. The repair video told me just what to do. I wouldn't have known about the belt tension otherwise.

Everything basically went as planned. Putting the belts on was a breeze, but I had trouble getting on the screws that anchored the pump in. The pulley didn't allow access for a nut driver or socket, even with a universal, there still wasn't enough clearance. I went back and forth between using a screw driver in the end of a socket and using the socket on the end of a tiny breaker bar. It wasn't bad, just took a little patience. Everything works like a champ now.

Same technique as the PartSelect video, except the result leaked to the outside at the outlet port because the two halves of the mold that made it were slightly misaligned, and there were two steps, one on each side of the fitting. Filed the steps away, and used Evinrude gasket sealant to make sure it wouldn't leak, and it didn't.

My husband did the repair. Since he owned a laundry quite a few years ago, he knew what he was doing. After hooking everything back up, the cold water was coming in hot. When hooking up the hoses, he had hooked the cold into the top intake. After watching the online video, he realized that the plate that was to be installed over the hoses, on the back of the washer, clearly stated "H" on top and "C" on the bottom. So we switched the position of the hoses and everything ran perfectly after that. I would suggest to ANYONE doing this repair, to watch the online video first, before starting, because it is very, very helpful.

Moved washer away from wall. Removed rear panel (4 screws). removed hose bracket (1 screw). use vicegrip to "open" hose spring clamp. Removed old hose, slipped spring hose clamp over new hose. "Opened" spring hose clamp put new hose over washer drain, released vicegrip. Assemble in reverse.

Watched your viedo, pulled the power plug, pulled the washer away from the wall and tilted back to expose the belts. Rolled the old belts off and put the new ones on. Just be sure to put the correct belt on the pump and agitator drive as they are a bit different. Adjusted the pump belt as described in the inclosed instructions. What was strange was the same instructions was enclosed with the aggiator drive belt which appears to not be adjustable. Once adjusted put washer back in normal position, plugged in power and was ready to go. Seems to work fine now, least no complaints from the wife.