Models > A102 Maytag > Instructions

A102 Maytag Washer - Instructions

All installation instructions for A102 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the A102
76-90 of 162
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer suddenly began to vibrate during a drying cycle

  • Customer: Bruce from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
After looking up the problem on the PartSelect website, which indicated the problem could be with the tumbler (drum) belt, I watched the instructional video, which was very helpful, as the dryer in the video was exactly the same as mine. After removing the power cord from the wall and separating the exhaust vent pipes from the dryer, I followed the instructions for removing the front panel, the front bulkhead, the drum and the old belt, which was worn and somewhat stretched. I then followed the instructions for installing the new belt, but I found it was easier for me to remove the back access panel in order to complete the installation of the belt around the drive pulley and tension pulley wheels as I wanted to see what I was doing as opposed to just "feeling" the belt to ensure a proper installation (e.g., new belt not twisted). Once I removed the drum, and before I put in the new belt, I also took the opportunity to use my shop vacuum (and you really need a shop vac for its power)to remove 25 years of rubber dust from the old belt, house dust, and packed lint from inside the exhaust fan, cabinet, and the vent pipes (and a dead field mouse that had crawled into the dryer through the outside vent pipe and had gotten trapped in the exhaust fan). I also examined the heater tubes to insure no lint was inside that and spun the fan blades by hand to make sure the motor shaft was not worn. Once I was satisfied that the installation of the belt was done properly, I put the drum back on, reinstalled the front bulkhead (checking to make sure the felt gaskets were in place, as recommended in the video) and reattached the front panel. I also took the opportunity to touch up the accumulated minor nicks and scratches ion the cabinet with refrigerator enamel. Now that the new belt is on, the dryer no longer vibrates, and with the dust, lint and mouse removed, dryer is operating much more efficiently. Remember to re-balance the dryer using a carpenter's level to minimize any latent vibration. Note that the actual removal and replacement of the belt took me about 30 minutes, and the rest of the cleaning, reattaching of the vent pipes, and balancing, etc. took about two hours.

Pulley came apart , frayed belt.

  • Customer: Peter from Westhampton Beach NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
Tilted washer on its side.Took off old pulley- Allen wrench. Slipped on new pulley and replaced both the drive belt and pump belt. Works like new again- maybe for another 29 years!!! ???

TUB DID NOT DRAIN

  • Customer: DAVID from LAKE CYRSTAL MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 3 people found this instruction helpful
RECEIVED DRAIN PUMP BY FED EX, PUT IT ON IN 15 MINUTES...MY WIFE WAS VERY HAPPY AGAIN....

Deteriorated and clogged strainer; slow water fill.

  • Customer: Richard from Jupiter FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 1 of 3 people found this instruction helpful
Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.

old belt smelled like smoke and was shredded

  • Customer: Everett from Glen Burnie MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
put on the new belt. it also smelled like smoke when we first ran. upon further inspection, saw that the drum was not turning easily. felt around the top inside edge of the drum, found the real problem- there was a sock jammed on the top edge between the drum and rim. removing the sock was easy, and then everything worked great!

tub would not spin

  • Customer: NANCY from HOLLEY NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
our neighbor had it done in no time!!!...

leaking water

  • Customer: Elise from TEMECULA CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
Took all the parts related to the drive shaft and replaced the tub seal. We also replaced drive and pump belts due to an overheating smell coning from washer a couple months back.

Water leak from underneath the tub.

  • Customer: Bill from Ypsilanti MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 1 people found this instruction helpful
I followed an the online video and the repair, my first stem seal repair, went fine. Kudos to PartSelect. The parts arrived in 3 days normal delivery. I saved $500 by not buying a new washer!

The impeller on the drain pump failed

  • Customer: Robert from Madison IN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 4 people found this instruction helpful
After removing the front cover and draining the tub, I replaced the drain pump and the washer works as good as new.

Washer leaked from below tub

  • Customer: Robert from Little Egg Harbor NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Socket set
  • 0 of 1 people found this instruction helpful
First unplug the unit. Removed the front panel. Removed the two hex head bolts from under the top at hte front right and left corners. Tip the top back. Unsnap the cover being carefull on the tabs. Loosten the set screw (bolt) on the bottom of the agitator and remove. Unscrew the retaining ring. Remember reverse thread. remove flange under that. lift out inner tub. Loosten the set screw (torx) on seal and unscrew reverse thread also. Remove rubber seal boot. Clean all surfaces and reverse the steps.

The agitator stop working

  • Customer: Glendora from Raleigh NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
My 13yr old son and I fixed the washer in about 5 minutes. It was very simple and easy to repair considering I had never done it before.

leaking from beneath the washer

  • Customer: steven from cape coral FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I followed the others directions and it's important to note that both nuts involed are indeed left handed threads. Also the it's important to know that[at least on my machine] that the set screw on the agitator is a torx headed set srew, not an allen srew. Other than that it was a pretty quick fix.

pump and drive belt was thorn

  • Customer: Henry from KITTERY ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Installed drive and pump belt.. very very simple. only tool required was a screw drive to remove front panel of the washing machine.

burning smell from washer

  • Customer: kevin from mundelein IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Replaced both the drive belt and pump belt in less than 10 minutes. Maytag has the easiest machines to work on.

belt went bad

  • Customer: Tina from New Haven IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Being a single Mom with no mechanical background, it went very well. I followed the instructions which were very clear. I did it myself!
All Instructions for the A102
76-90 of 162