Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light Bulb
Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Slid two latches at rear of bottom oven pan toward door, pulled pan up at rear of oven and removed. Igniter exposed, removed two self-tapping screws with nutdriver, pulled wires surrounded by insulation up out of hole in ovenfloor an unsnapped plastic connector wired to old igniter. screwed new igniter to bracket, reconnected wires, pushed connectors into hole and shoved new insulation around wires, fitted bottom pan and turned on oven. Works better than new, Thanks PARTSELECT.
If you watched the video on installing the part it IS that easy. The connector piece matched exactly with what my oven already had so it was as simple as disconnecting the old piece and plugging in the new piece. There was no hidden challenges or obstacles to overcome. The oven works perfectly fine there was a slight smell when I first turned on the oven but I am attributing that to a new part. The smell did go away. I am 24 years old and a female who has limited knowledge in electrical/oven work.
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Oven burner would periodically go out and re-light
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.
Once the part was free, the rest of the repair went quickly . At that point: - Pull the element leads enough to get to the plastic connector - Disconnect the old part - Connect the new part - Re-attach to the bracket with new screws.
First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3
I researched the stories on Partsselect, and it looked like this would be a simple repair. Fortunately, it was more simple than I'd thought. We bought the house (and stove) used, and the ignitor apparently had been replaced before, because the part was an EXACT replacement for the old one. I simply unscrewed the two screws holding the old ignitor onto the bracket/burner, pulled the wiring from the back of the oven through the insulation, disconnected the snap connector, reattached the new one. Then I pushed the wiring back through the insulation and added some additional insulation (provided with the part), making sure all extra length was pushed into the insulation. Reattached with two screws using a nut driver, replaced the bottom pan in the oven, slid the door back on its two hinges and started it up. Works perfectly. Thanks Partselect. You guys are great and I had the replacement my mail in about 5 working days!
took out both racks and under tray at bottom of stove no tools required. used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in. clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like new .
The trickiest part was making sure that the correct part was ordered. The first attempt was a failure. The seal was too long and the clips were too big. After finding the correct part it was a breeze.
The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...
Removed bottom tray of oven, unscrewed gas pipe, removed old igniter and replaced it. Spent some extra time digging around for leads, etc. before discovering that my new igniter was identical to the old one and all I had to do was plug it in.
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.