85161 Amana Refrigerator - Instructions

removed old icemaker and transfer some of the parts to the new icemaker. The only problem was that I had to disasemable the new icemaker to replace the fill tray with the older style (which was included). Once that was done, installation was pretty easy.

I removed the old ice maker as described by the DIY video and had no problem except, I had to remove the ice tray from the motor section so the end cap could be changed. This only required removal of two Phillips screws on the case of the motor assembly, that are used to to secure the tray. Once the tray was off, the ice ejector could be removed and the end cap was free to change. Everything was re-installed in reverse order and unit was mounted. An FYI to anyone with slow ice making, will need to check their freezer temperature. Make sure it's set to get as cold as 5-10 degrees Fahrenheit. After installing new maker, it was not making ice fast enough, only to find my freezer temperature needed to be changed as well. Everything is working as it should now.

My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!

Repair turned out to be unnecessary because the compressor was just not supplying adequate cooling. Need new compressor or fridge. Condensor clean fan working, evaporator is ice free and fan working, defrost timer working, thermostat ok and cold control tested good. Fridge runs all the time but never satisfies cold control setting.

The ice maker was easily replaced, however I still had no ice. I ended up using an on-line repair service which determined that the problem was the water inlet valve. Replacing it was beyond my expertise so I hired an appliance repairman.

just as video instructions said, very easy just following them ,part arrived in very short time and was exact fit completely satisfied, saved repair man service charges and wait time

After reading the articles previous owners wrote, I tackled the repair. There were no big problems until I had to change out the water line on the icemaker tray--that part was for a different frig--so it had to be changed out with the Amana water line part that was enclosed. I couldn't get that part removed, so I had to have my husband change it out. He then finished the installation. Everything went smoothly, just my pride wanted me to finish it all by myself.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and it works like its brand new. Thank you PartSelect!

This a top refrigerator with a bottom freezer. Turned freezer temperature dial to the off position. After removing everything from the freezer compartment, remove the back panel hex screws (7) total. Removed panel. Placed large fan in the freezer compartment on high for about 40 minutes to sublimate all the ice on the freezer coils. Removed and replaced the defrost thermostat on the right side of the compartment, it is clipped onto the coils. Replaced back panel and screws. Turned freezer control back to previous setting. It's been working fine for weeks now. Old part was ruptured, apparently from overheating (internal contacts became too resistive) during a defrost cycle.

Watching the video made this dead easy. If I had a newer refrigerator, I suspect it would have taken 10 minutes. Since I have an older 'fridge, I ran into two issues not in the PartSelect video. First - there were no "clips" to slip the icemaker into/out of, the unit was screwed directly into the freezer wall. Kinda hard to see the screws, especially the one in front, but not a big problem. Second - there is a wire-harness clip at the back side of the icemaker, that hooks onto the ledge of the back connector, just under the screw. That clip had slipped, and until I figured that out and reseated it, it made getting to the rear screw wit the nutdriver a serious pain. Other than those two issues, though, the job was exactly as easy as the video makes it look!

Cubes in bin were freezing together due to water leaking from the ice maker assembly. Replacement went easy with bin rails removed.

1. removed bottom screw. 2. pinched sides of rear connection to disconnected ice maker (noted red wire on top in cabinet rear). 3. bump out old unit taping to release tab on bottom. 4. disconnect wire from icemaker and remove wire holder with philips screwdriver.ew ice maker. 4. reattach harness to new ice make and replace clip. 6 reattach l bracket to bottom of ice maker. 7. detach shut off wire from old ice maker and replace on the new maker. 8. place back into position in freezer compartment. 9. reattach water delivery tube 10. connect wire to rear of cabinet. If motor drive still good on old maker scavenge before throwing away bad parts.

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

Took out socket, replaced new bulb in new socket and plugged in. Easy!