7MMSE7999TW0 Maytag Washer - Instructions

diconnected water supply and discharge, unplugged the unit, removed the aggitator, laid the washer on it's back, romoved the hoses from the pump, took out 3 bolts, removed the motor/transmission and replaced the clutch and put it all back together.

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

with pliers removed remaining broken part on selector switch
attached new knob sliding fool proof groves on innerside now we are back in business, myself and family thank you for the support

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

After reading other comments about lid switch replacement , I knew the front of the control panel would move forward and lift off. Although none of the descriptions mention the steel clips that were also use to hold the cover down. It does take quite a bit of presure to pry these up and loose before panel would move forward. Would recomend putting tape on both washer and screwdriver to protect washer.

The only tricky part was figuring out how to get to the part. There were only two screws that seemed likely candidates to pop off the control panel (on the back at the corners). Fortunately for me the obvious answer was the right one...the panel lifted up and the new part went in - very easy.

This was really easy and the part came in like 2 days. All I needed to do was flipthe washer on its side and remove the old hose...a couple screws and install the new one...it was a perfect match so ...no issue.

Ordered the part, received part in short time and snapped it on in less than a minute. Seals better than original.
Thanks PartSelect. I will be back.

I first watched a YouTube video on how to open up the machine. It was a breeze. I removed the part the hose attaches to where the water comes out and into the tub. The hardest part was removing the old hose clamps. Had I known I would have used new clamps. I took off old hose and replaced with the new one, it took longer because of the clamp issue. Otherwise it went fairly easy, to my surprise. Even tho I am a 70 yr old woman I will try to fix what I can. Doing this saved me at least $600. For a new washing machine. I'm so proud of myself.

Unplugged the main power. Removed the 2 screws in the back and top of the control panel. Pulled control panel forward and tipped towards me to remove from top of washer. Removed the ground wire screw with a socket/ratchet. Removed the switch by pressing the tap inwards. The tab was brittle and broke. Replaced the switch, ground wire with screw and the control panel. I notice that the 2 screws which secure the switch lever/hinge to the lid were loose. These 2 loose screws were actually the problem in the first place. The loose lever was not making good contact with the switch. I think the switch was actually fine but since I broke the tab on the switch I needed to replace it anyhow. Plugged in power cord and washed a load.

Purchased lid trigger elsewhere but got the connector on line here after being told I would need to purchase complete wiring harness to correct. Once lid trigger was in i stripped the three wires that went to lid trigger and pushed thru the back side of the connector. Then I plugged into trigger. Now washer works again. Very easy to do.

Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicates the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.

I followed the online instructions to remove the shell and attempted to remove the drum, but not having the special wrench to remove the special nut, tried using a screwdriver and hammer, which failed to loosen the nut. I then started examining the the undercarriage and saw that I could replace the springs without removing the tub and did that. In the course of replacing the springs I discovered I could also access the wear pads by lifting the drum off of the undercarriage and placing a block to hold it above the pads. I was able to pop the old pads out by tapping underneath them with a hammer. The new pads were then installed and the weight of the drum popped them in. It was necessary to lift the drum assembly three times for each of the three pads.

First read up on what others did and tried to find free repair manual with little luck. Called repairman, they thought whole transmission was shot- would have been $70 just to have them look- forget it. Getting it apart: popped off the two console cosmetic panels to get to a screw on each side from the top. Lifted off console, levered and squeezed retaining clips. Unhooked two connectors and overflow tubing? Shell pulled off easily, getting back on after I was all done made me wonder if it was a good choice. In the end yes- allowed me to clean inside surfaces of both tubs to remove grime and rust. There are many stories on the actual clutch replacement, so won't go into too much detail but some lessons learned. Keep track of the way all the plastic aggitator pieces go in, plus the washers and clips along the way. Deep well 1/2" I think socket for the tub, it's litely spring loaded so look before you set it down. Punching off the nut on the tub worried me, but it was no big deal. Loosens and tightens the normal directions, no positive tight stop, just compression so pay attention to how tight and hard you pounded to get it off. Drain the water from the inner tub before getting too far. I took the four springs off and removed both tubs to clean. No more complaining about brown spots on clothes. Get the whole clutch kit, not just the band, even though it's probably just the band worn out. The plastic clutch engaging piece will probably be fatigued. The motor etc is heavy, and buffered it's drop with rags. tip on side when putting it back, because its a bear to try to lift up. I lightly greased some moving parts, just not much as to not cause band grip problems. The wire retaining clip is tricky- I put the hook end in first, used pliers to try and compress, and screwdriver to push down and in. The whole things wants to spin while you do this, but when it finally goes, it stays. I was concerned about the location of the band spring in relation to it's actuator when putting it together, but it turned out if you put it anywhere where the clutch is free to spin, it will engage normally. The top lid has two rubber bumpers, one fell off and landed on the front bottom corner of the cover which didn't help reinstallaion until my 8year old noticed it! Took a number of tries but finally got the four guides from the frame into the cover. I tried bringing it in level, front tipped sligthly up, front tipped slightly down; in the end I won't be much help, it just finally went. It wasn't as easy as most people said it would be, but my back hurt and I had kids "help", and it took just under two hours. Works amazingly well now. Parts arrived Two days after ordering, with no expiditing!

I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago