Quick Question!

Have you ever purchased from PartSelect.com before?

11747965-1-S-Whirlpool-WPW10001130-Foot, Front - Single
11747965-1-S-Whirlpool-WPW10001130-Foot, Front - Single 11747965-2-S-Whirlpool-WPW10001130-Foot, Front - Single 11747965-3-S-Whirlpool-WPW10001130-Foot, Front - Single http://www.partselect.com/Schematics/Maytag/IFMSPDID.gif

Foot, Front - Single

Compare At

$3.37

You Save

$.56

Your Price

$2.81
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11747965
Manufacturer Part Number WPW10001130
Manufactured by Whirlpool

The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.

This part works with the following brands: Whirlpool, Kenmore, KitchenAid, Maytag, Roper, Estate, Inglis, Crosley, Amana, Admiral, Jenn-Air, International, Magic Chef.

This part works with the following products: Washer, Trash Compactor, Washer Dryer Combo, Dryer, Wall Oven.

This part fixes the following symptoms:

  • Shakes and moves.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.7 / 5.0, 5 reviews What's this?
1-5 of 5
 

45 of 62 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Paddy from Ferndale, WA

Bearings went out in the drum.

purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in..

Help other customers find the most helpful instructions.

Were these instructions helpful?   

15 of 31 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Customer: Randy from Atlanta, GA

Broken water inlet syphon combined with missing feet was causing water to spill out of the washer

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Ernest from Midlothian, VA

No agitation, no spin, pump ok

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Foot, Front - Single
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Wrench (Adjustable)
Customer: Rick from Lennon, MI

Bought a washer without front leveling feet

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 160 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Wrench set
Customer: kaine from butler, PA

Washer not rotating

Washer not rotating, removed the control head and back cover. Then removed body housing around tube to get to the bottom. had to replace coupling on motor then removed the agitator tower and replaced the Parts for the tower agitator. unit is 16 years young and still looks and runs new, put a total of 55 dollars into repair and it should be good for a long time. This is with a family of five. Washing 2 loads everyday.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11747965
Manufacturer Part Number: WPW10001130
Brand Model Number Description
Kenmore11010202000Washer
Kenmore11010202001Washer
Kenmore11010502990Washer
Kenmore11010502991Washer
Kenmore11010852990Washer
Kenmore11010852991Washer
Kenmore11012202100Washer
Kenmore11012502100Washer
Kenmore11012852100Washer
Kenmore11013202200Washer
Kenmore11013212200Washer
Kenmore11014102300Washer
Kenmore11014112300Washer
Kenmore11014202300Washer
Kenmore11014212200Washer
Kenmore11014222300Washer
Kenmore11014502300Washer
Kenmore11014852300Washer
Kenmore11015732400Washer
Kenmore11015842400Washer - Kenmore Washing Machine
Kenmore11015852400Washer
Kenmore11015862400Washer
Kenmore11015864400Washer
Kenmore11015942400Washer
Kenmore11015942401Washer
Kenmore11015944400Washer
Kenmore11015944401Washer
Kenmore11015952400Washer
Kenmore11015952401Washer
Kenmore11015954400Washer