Models > 7MMSE7999TW0 Maytag > Instructions

7MMSE7999TW0 Maytag Washer - Instructions

All installation instructions for 7MMSE7999TW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7MMSE7999TW0
76-90 of 214
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken water inlet syphon combined with missing feet was causing water to spill out of the washer

  • Customer: Randy from Atlanta GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 7 of 19 people found this instruction helpful
I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

Won't spin clothes properly. They were wet

  • Customer: Stanley from Santa Clarita AL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 2 of 4 people found this instruction helpful
Removed bolt from agitator assembly. Pulled up on the agitator vane and removed it.
tipped over macvhine . Drained water from tub via the drain hose assemble and removed clips from the hoses to the pump atached to the motor and drained residual water from the lines. Removed the electrical connector attached to the motor assembly and the three bolts holding the motor assembly and shaft to the tub and slid the shaft and assembry out.. Took digital photo of the assembly to insure proper part replacement and removed the clips and spring that are part of the assembly that holds on the clutch. Removed the old assembly and installed the new assembly . Installed the spring and retaining clip that came with the kit and installed the shaft . Installed the three bolts holding the/motor assembly and shaft in place and reconnected the hoses to the pump assembly and reconnected the electrical connector. Uprighted the washer and everything worked like new when I tested the spin cycle. I was quoted $225 to fix the bad clutch from the appliance tech that I paid $20 to diagnose the problem . Saved about $175 by doing it my self and it wasn't hard to do. My thanks to the previous persons that had done the repair and left iinstructions on how to do it.
SW Santa Clarita Ca.

would intermittently fail to spin during rinse cycle

  • Customer: Robert from Covington WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
Watch the video. Remove agitator. Disconnect power and water supplies. Lay machine on its back. Unclip and move pump out of the way. Remove three bolts securing motor assy. Slide motor assy and agitator shaft away from tub. Remove a washer and c-clip to slide clutch assy off of shaft. Install new clutch and reassemble machine. Total time to repair is about 30 minutes.

lid gasket became older and brittle and eventually broke and cracked

  • Customer: kenneth from oregon city OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Ordered the part and a couple of days later I popped off the old and popped on the new. It took longer to remove the part from the box than to install it.

The original seal on had deteriorated and was coming apart.

  • Customer: Sandra from Hamilton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Really nothing to it, especially since the original seal was coming apart. I just ripped it the rest of the way apart and removed it, then slid the new one on in its place.

Cracked, broken seal

  • Customer: Ronald from Glenwood MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The old seal had become brittle, cracked and fragmented and would no longer fit in the slot. Without it, washing had become a real mess. I took the new seal and snapped it in within a few seconds and was back up and running again. I looked everywhere for this seal, but this site was the only place I could find it. Thanks for having such a wide range of parts. This inexpensive broken part had made my machine unusuable. If it were not for you, I probably would have to resorted to a Sears appliance technician who would have charged $60 for just showing up.

rubber seal broke aprt

  • Customer: Lisa from North Attleboro MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.

rubber lid cushioning strip broke

  • Customer: Bruce from Hammett ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
the original piece had 3 metal clips that held the strip in place. It was a matter of sliding the strip off and sliding the new replacement part on. Time involved was less than one minute. It took longer to find the part than to install it. The part was ordered Thursday night and it was installed by Monday! Great service!

The washer lid seal was torn and because, I think, I was getting a moldy/musty smell from the washer and in the clothes.

  • Customer: Erik from Atkinson NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
It was simple slide off the old seal and then clip on the new one. I also want to thank the workers at Parts Select, it was very simple and everything went great. I will be using them again and passing the word on.

The temperature sensor in the water mixing valve quit working. It would operate on manual, but not auto.

  • Customer: james from arlington WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
As with any repair job, the hardest part is getting started and figuring out how to take it apart. I first tried to remove the top, by prying up on it,( his has worked in the past). This only broke the plastic retaining clips. I then removed the two plastic covers on each end of the control panel, then the two screws that hold the front of the control panel down. and lastly slid the control panel forward and out of its slots. I then used a 5/16th nutdriver to remove the four screws from the back panel. Now I was able to pull the panel back away from the washer body enough to use needle nose pliers to to remove the four electrical plugs located on the mixing valve. I used a felt tip marker to identify the locations of each plug. I used a 1/4 nut driver to remove the one mounting screw that held the valve in place and removed the valve. When the new valve arrived, It took about 15 minutes to re-install the valve and put everything back together.

wow!

  • Customer: Sheila from Borger TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I received the order quickly (although thought it could have been packaged in a much smaller box) and it took less than 10 mins to remove the old seal and replace with the new one. Only problem is the seal I ordered wasnt causing the problem ..lol so will be ordering again!!! Thank you!

Lid seal was torn

  • Customer: Debra from Ridgway PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Pulled off the old torn seal & in about 15 seconds had the new one put on, couldn't have been easier.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 12 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

the rubber lid seal had torn and was falling off of the lid.

  • Customer: VICKIE from MEQUON WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
I removed the torn part which just pulled off of the lid and snapped in the new piece. No tools were needed. I also wanted to add that it was great doing business with Part Select. The part came well packaged, it came in a timely manner, and it was the correct part ! I will try Part Select for any of my future repair part needs.
Thank you

Washer needed help to spin out

  • Customer: Timothy from Erie PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 1 of 3 people found this instruction helpful
removed the old clutch assembly. Then replaced with the new clutch assembly and it works great.
All Instructions for the 7MMSE7999TW0
76-90 of 214