7MMPD6845TM0 Maytag Washer - Instructions

Remove the sides of the washer, motor ran but nothing moved, closer look found drive coupling broke (10 years and it made of plastic) Order a new part from you, arrived very quickly. Install the part 10 min. later it was running.

took 5 minutes to repair just read direction

We followed the step by step video that you had posted for those parts. It is now working wonderfully. The repair man had told us it could not be repaired. Thank you so much for having these do it yourself instructions.

Followed the video did not need to tilt machine over. Layed on floor it was more comfortable. The most difficult part was putting back on the tension band on top that's because I got a little tired on the food. Thanks for all your help. I bet I saved over $250.00 if a service tech came to fix this. You guys are the best

Once you take the housing off it's only two clips to remove the water pump from the motor, then two screws and two more clips to remove the motor itself. One issue I ran into was the new coupling was hard to put on, so the first time I did I overheated the motor because it was binding (was also very hard to get the motor back on). After taking it apart again, and slightly tapping both couplings with a hammer the motor went on very easy and washer works like a champ!

Replaced the lid switch by pulling the washer out enough to gain access. Not necessary to disconnect the waster hoses. Remove the two screws from the white plastic tabs on the rear of the control panel. Also remove the two screws connecting the control panel from the washer body. Lift the lid slightly and pull the control panel forward. Disconnect the pug into the lid switch and remove the switch. Replace the switch but remember to lift the lid while doing so. Lid has a small arm that must engage the switch correctly. Replace the control panel and reinstall the screws. Repair is very simple.

I took apart the cover of the washing machine, remove the back, and disconnected the hoses , also disconnect the controls,remove the pump and the motor,which are ben hold by two brackets, then proceed to remove the old parts and insert the new ones, the only problem is that they fit too tight and I used a round tool to insert the new ones, after that i put everything together and bingo, the machine is working already.

Your video was very helpful in showing steps for repair so I didn't have to discover how to disassemble. The old Direct Drive Motor Coupling had three broken couplers on one side and a cracked center on the other. New Direct Drive Motor Coupling was a much improved design that should last even longer than original. The couplers metal sleeves and overall thicker part was what original should have been.

This was a great buy!!! All the hose clips as well as the hose retainer came installed on the new hose (in the correct location) the hardest part was waiting for the part to arrive...it took me least three 2 minutes to install...if my dog had thumbs he could have replaced the drain hose.

I Googled "washer would not spin" and came upon the PartSelect YouTube video on replacing the motor coupling. Since this seemed easy enough (and I'm a 40-year-old Mom), I decided to take the washer apart as the video instructed just to see if I could find anything obviously broken or out of place. Low and behold, the rubber gasket around the coupling was broken and indicated the coupling probably was too. I ordered the part through the direct link on the YouTube video and easily put the new coupling on and VOILA! The only thing I'd recommend differently is that you leave the pump alone. It doesn't need to come off to get to the coupling. After wrestling with trying to remove the pump, I left it in place, but not before unknowingly damaging it. I had some rust build-up in there and it made the fit very tight and cracked the part/sleeve the motor drive plugs into. When the washer was reassembled I found I'd caused a leak. But...no biggie. I decided to replace pump, too. Hey, now I know how to! :) Just received that part yesterday and VOILA! It's amazing what you can accomplish with the internet. Don't be afraid of this task, ladies (and gentlemen).

I surfed the internet with my model number. i found partselect.com. I read the comments and diag.'d my problem. I ordered the parts needed. I recieved the parts in 3 days and had it fixed in less than 10 minutes. VERY EASY!

watched video and followed instructions, no problems.

took the washing machine out of the washroom closet and did the repair in the kitchen

Replaced the clutch - works great. HOWEVER - check the drain pump attached to the motor, there was a small sock clogging it up which also fixed the problem. I saved 600 bucks on not buying a new washing machine!!

Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!