7MMPD6845TM0 Maytag Washer - Instructions

removed the two screws that attached the top to the base. lean top back to access the lid switch. install the new one; best to have door open when installing. real easy repair that saved me mucho dinero.

I watched the video and that was a great help. I just entered my model number and selected the symptom. 61% of the time the drive coupling is the problem and it was. Ordered the part and got it the next day.

Removed the control panel and the cabanit. Then removed the adjutatior . Removed the motor and gear box slid the old shaft out and put the new one in put back together. Took about one hour .

First off, let me say two things, this was my very first washer repair and the installation video was excellent.

Few things though ..... The first thing I noticed was the old parts I removed did not look that bad to me. I was starting to wonder if I was wasting my time. However, its apart now I'll continue on. I had a hard time properly seating the new couplings on either end correctly. They were VERY snug. What I ended up doing was getting a 20mm deep socket that fit perfectly onto the coupling and with a hammer gently, (and I underline gently) tapped the new parts into place. That fixed that problem. I also had some minor difficulty putting the cabinet back together, but nothing earth shattering. The cabinet fits on top of the frame, not under. And lastly, the small clips that hold the console on were not very reusable afterwards so I'll need to order a new set of them sometime.

All-in-all it was a fun repair that didn't take me too long and I saved quite a bit. I definitely would do it again if necessary. I've done about 5 loads of laundry since and everything seems to be working great so far.

- Bob

Unplugged the washer and removed the two screws from the control panel. Raised the control panel and disconnected the wire connector that connected to the top.Then removed the two spring clips that hold the cabinet to the back of the washer. removed the cabinet from the washer that exposed the frame of the washer. I then replaced the broken spring by pushing the tub of the washer as far as it would go and replaced the suspension spring. Then i reinstalled the cabinet and control panel. Everything worked okay. ood as new.

The video they provide was very easy to follow. The only difference from mines and the video they provided was the top portion. Mines was held by two Phillips screws on the switch housing. The top pulls forward. Everything else went accordingly. Take off switch plugs, take off washer cover, unplug the vacuum line, replace coupler and reinstall. Only thing that took up time was getting water off the floor when I pulled the vacuum line. Use a bucket or do it outside.

My repair was successful but was not as easy as some have reported. I needed to replace the coupler, but when I tried to remove the pump from the motor, the shaft was rusted and wouldn't budge. I pried and wiggled and used WD-40 to no avail. I ended up taking off the motor and pump as a unit. After replacing the coupler and reassembling the washer, the water pump leaked, probably as a result of all of the prying. To get the water pump off, I had to cut it into pieces, using a hack saw. Even when I got down to the end, I had to peel pieces of plastic off of the rusted shaft. I then had to file and sand the shaft to get it so that it would fit into the new pump. After putting the washer together again and running it through its cycles, I noticed that the top half of the agitator was not turning. I then ordered and installed the agitator repair kit. Through all of this, my orders were all correct and arrived in amazingly fast times. The videos were all very helpful. Even though it was a trial a times, I still saved a pile of money.

First watched YouTube video "Kenmore/Whirlpool washer not spinning", excellent video .Disconnected water hoses and drain hose. Unplugged the washer from the outlet. Removed the agitator from the washer tub then tipped the washer backwards resting on a secure block of wood for support not fully on the floor. Removed under insulation, removed both water pump hoses. Have towels ready when hoses are removed, there is still water in the hoses. Removed the water pump, disconnected the electrical connector from the pump motor, removed the bolts from the motor that attached the motor clips, removed the motor clips from the bracket and removed the motor assembly. Video shows motor, bracket and gearbox removed as one unit. Very heavy. Remember motor position on the bracket for reassembly, I used yellow marker. Removed the bracket the mounts the motor. Removed the bolts for the gearbox and began to lower the gearbox. The agitator shaft on the gearbox is pretty long so I had to tilt the washer some more to remove. After the gear box was removed I could now see the spin clutch, which according to the video was definitely bad. PartSelect had the correct part, reasonably priced. Ordered normal FedEx delivery, part arrived in 2 business days. Instructions came with the part for very easy installation. Installed the new clutch and reassembled the washer. Before reconnecting the washer hoses and drain, I plugged in the washer, manually placed timer on spin, washer spun, could not see spin but felt washer in spin cycle. Reattached water and drain hoses. Filled washer empty with cold water and placed timer again in spin cycle. Water drained, no leaks under washer or from hoses, spin cycle good. Repair done, works great.

removed motor and broken coupler... installed new coupler and replaced motor. also removed pump to inspect for sock, etc. that that might have caused coupler to break.. ADVICE: Look for how-to video on YouTube first. Remove outer cabinet according to video by first removing the top control panel and then remove the outer cabinet which exposes the motor and pump. This way you will not have to tip machine up/back and work under it. This repair is made easily by first removing the outer cabinet.

I followed the instructions from a YouTube video, just do a Google search for the make, model, and what the problem is and several videos will come up to pick from. Everything went just as described in the video, took about 10-min to take the motor out, a couple of minutes to replace the broken motor coupling, and another 10-min to put it back together - slick.

Watched the video on your site for that part

Before I even watch any partselect videos to do the repair, which I should of from the very beginning, ah, ja, ja, I had already disassembled the back panel "my way" to the washer and trouble shooting the washer with my wife's help. While she tilted the washer backwards, I looked under and we found that the noise was coming from in between top of the motor where the direct drive motor coupling is located and the clutch assembly came together which I learned along with names and functions after watching the partselect installation video. Nice! Once I received the part it took me like 45 minutes to put all back together. Took loose two screws to clips holding the motor, pulled motor of mounting bracket finding the broken piece, replaced it, recouped reinstalling motor onto the motor bracket, clip, clip the two little screws and walla, got the wife her washer back, at bed time rewards, peace of mind the rest was history... Thanks PartSelect for awesome videos and great customer service!

I watch the you tube, and try to fix it by myself,to save money, and moving trouble.this is my first time fix a big machine like this,I was a little scare, but after I saw the youtube about how to fix the washmachine,I start to give a try.it take little bit more time for me to figure out ,but I finally made it. now I can wash my cloth now, and perhaps fix washmachine for my exrat income.( message sharing from an asian 58 yrs old lady, sorry for unable to show step by step due to English not very good)

Followed the video and instructions included with part. At first we did not think the repair was successful, but after several small loads were run, squealing stopped. The washer is 16 years old and so far is running like new. We certainly appreciated the great customer service. The part was delivered in less than 24 hours.

very easy, pop up the top, unscrew 2 screws, unplug switch , plug in new switch replace 2 screws ,put top down,finished