Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Light switch in freezer side got broken
Took a putty knife and Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place
Steps to replace Whirlpool evaporator fan motor 1. Watch numerous DIY Youtube videos 2. Move frozen food to refrigerator section, close refrigerator door 3. Cut power to refrigerator 4. Remove all shelves and bins in freezer section 5. Back panel has two parts, a top and a bottom section 6. Unclip small shroud covering screw bolt in upper left corner holding top panel. Remove screw bolt 7. Gently pull and work top panel out 8. Remove screw bolts from all four corners in lower panel and remove bottom panel 9. Verify power has been turned off 10. Unclip grounding wire 11. Unclip evaporator fan motor from power 12. Remove whole cradle holding evaporator fan motor. Note orientation of cradle. Fan blade is slightly angled toward the back of freezer. In other models, the cradle may not be removeable. 13. Remove plastic fan with firm pull 14. Unclip bottom brace to remove evaporator fan motor 15. Replace old grommets in bottom brace and on top of evaporator fan motor with the new grommets 16. Install new evaporator in cradle and clip-in the bottom brace 17. Install new fan blade on motor 18. Place cradle with new evaporator fan motor back in freezer 19. Reclip power and ground wire 20. Turn on power and test if working correctly 21. Turn off power 22. Complete steps from 8 to 2 in reverse
Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced. reassembled the pieces.
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Raise side of fridge and slide 2x4 under side with broken wheel.
Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.
Freezer work perfectly, Refrigerator Stopped getting cold, water line froze, there was ice Forming around the condenser in the bottom of the refrigerator behind the drawers
Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator. First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them. Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
