All Installation Instructions for Kenmore Range 66575775890

Oven was overheating and locking the door. Codes indicated the temperature sensor could be the issue.

Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!

Parts Used:

Temperature Sensor

Margaret from PUTNAM VALLEY, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One burner would not light automatically, needed match to use

Unplug the electrical cord. Remove all the grates and burner caps. Remove the two philips-head screws on each burner. Slide the plastic putty knife under the cooktop in the front to locate two clips. Push in to disengage clips and lift cooktop up in front. Disengage cooktop from the rear of the range. Remove the bad igniter from the burner head and replace with the new, Disconnect the wire from the spark module and install the new wire. Replace the cooktop by securing the rear first and then lowering into place until the clips engage. Replace the philips screws on the burners and the caps and grates. Plug the range back in and you are done.

Parts Used:

Spark Igniter

Charles from MELROSE PARK, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The igniter for the front left burner was shorting out at the base of the ceramic preventing the burner from lighting.

Unplug the stove. Remove the burners. Release the top of the stove by using a screwdriver to push in the spring clips on each side of the stove top. Pull out stove to access the back of the stove. Remove the back plates. Identify the defective igniter wire and remove. Install the new igniter wire. Screw the back panels back on. Snap the stove top back in place. Reinstall the burners. Push the stove back into place and plug in the stove. Test the burners.
One precaution - make sure you do not move the gas tubing under the stove top out of position. If you do, make sure you put it back in line with the gas valves.

Parts Used:

Spark Igniter

Michael D from FULTON, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

THE OVEN WAS NOT HEATING TO DESIRED TEMPERATURE

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.

Parts Used:

Temperature Sensor

Heriberto from AUSTIN, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The side trim on the glass door needed to be replaced.

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

Parts Used:

Hinge Pin Kit

Mary from LARAMIE, WY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Pan scratched by housekeeper

Unscrewed old pan and screwed on new one.

Parts Used:

Interior Bottom Oven Panel

Kenneth A. from SANGER, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken glide

replaced glide with screwdriver. very easy

Parts Used:

Front Drawer Glide

Rear Drawer Glide

Andrew J from MASSAPEQUA, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven light not working

replaced light socket but did not repair problem. must have burned the motherboard.

pleased with service from your company.

Parts Used:

SOCKT-LITE

Richard from Gaylord, MI
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

slides on lower drawer were broken

I used a phillips screwdriver and replaced the part with one screw.Very easy and replaced my lower drawer under my oven,it tool about three to five minutes at the most and my drawer works fine now.Thanks for the instruction video on line, it really helped.

Parts Used:

Rear Drawer Glide

Leona R from Louisville, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

door glide broken

removed the old ones.then installed the new ones.

Parts Used:

Rear Drawer Glide

David from Port Orange, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

range handle fell off and screw got lost

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

Parts Used:

Screw

Frances from palm beach gardens, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Inside Light would not work

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

Parts Used:

SOCKT-LITE

Dan from Caddo Mills, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I shattered the original one when I took it out to clean it.

I placed the new glass in place, and replaced the screws. What I really want to tell abut is how QUICKLY my replacement part came from your company. I was so upset when I broke the original glass, but the replacement glass arrived within 24 hours! It was wonderful! Thank you!

Parts Used:

Exterior Door Glass

Kristine from Drexel Hill, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

9 of 29 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drawer glide was missing and the trim on the door was broken

Ordered the replacement part., removed the old trim from the door and reinstalled the new trim. On the drawer glide, I simply reattached a new one to replace the one missing.

Parts Used: