Models > 66575775890 > Instructions

66575775890 Kenmore Range - Instructions

All installation instructions for 66575775890 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 66575775890
76-90 of 95
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door trim (sides and bottom) needed replacing.

  • Customer: Ralph from Canon City CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the bottom drawer. Remove the two Phillips head screws on the top inside of the door. Pull up on the handle (CAUTION: Be sure to hold the glass front against the door while doing this or the glass front can fall, possibly damaging it. Remove the glass front by lifting it towards the top of the door. Remove the two side pieces and the bottom trim piece by unscrewing the Phillips head screws located on the underside of the bottom trim piece. Discard the old trim pieces. Attach the new metal bottom trim piece using three of the previously removed screws. Do not tighten the screws at this time. Each plastic side piece has a nipple at the bottom. Insert this nipple into the outermost hole at each end of the bottom trim piece. The edge of the flange on each side piece should face inward. Have an assistant hold the two side pieces against the door frame while you slide the glass back in. The inward facing flanges go UNDER the glass. Reinstall the top piece making sure the indentations at the top of the side pieces are under the top piece. Install and tighten the two screws that hold the top piece on. Tighten the three screws holding the bottom trim piece.

electric oven not holding set temps.

  • Customer: Charles from Star ID
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My wife was complaining about poor baking results with the oven in the home we just purchased, so I hooked up my digital temperature meter and found it was almost 50 degrees of, so I tried the ovens off set program to bring it closer into range. That did the trick ,but she complained about poor baking still. I watched the oven cycle about 8 times and saw her problem. The oven was inconsistent when dropping below set temps, some times it was 20 degrees off, other times it was 80+ degrees off before the element kicked back on. I started with the sensor, it came with easy instructions including wire hi temperature wire nuts if the connectors didn't match... which they didn't. It was very easy to access the senor for replacement. Just unscrew about 10 screws, pull the back access panel off and there it is. Cut the connectors on both ends making sure to leave plenty of wire on each end. Wire nut them together and reinstall the back panel. Reset the oven off set back to zero and check the oven temp watching about 6 cycles. Comes right on now, and her first baking effort came out great...I am pretty sure that was the problem.

Igniter was glowing but not enough to catch the catch the burner

  • Customer: Bruce from Dacula GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Really quite simple. Remove the racks - remove the two screws in the back of the bottom plate - slide out. remove the bottom drawer. remove the two screws holding the igniter - unplug the old igniter and remove. screw in new igniter, plug up new igniter, replace bottom drawer, replace bottom pate, replace racks. I did turn off the gas and electricity to the unit before repairing - and it was easier for me to get behind the unit to unplug/plug the igniter. works great! thanks!

Oven not heating to set temperature

  • Customer: Mitchell O from Williamsburg VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the back access panel of the stove. Removed 2 screws holding the temp sensor, replaced temp sensor, Installed back panel. Done 19 minutes.

Broke front glass of oven while moving

  • Customer: melody from springhill FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Looks better than the old one wes and so easy to do. Thanks.

Dented front trim

  • Customer: JAMES from WESTERVILLE OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced trim kit found on site. Everything went well. No real problems. I will book mark your site for the any other parts I may need.

Damaged Socket When Removing Bulb Base

  • Customer: Charles from Oceanside CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Broke outer glass on oven door.

  • Customer: David from Sullivan IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Repair relativley easy only needed phillips screwdriver to complete repair.

Little or no heat when baking

  • Customer: Warren from Mukwonago WI
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
That should have been an easy repair according to previous responders that replaced this part.

The first issue is the Phillips head screw that fastens the sensor to the back of the oven was frozen and I had to drill it out.

The second issue was I could not pull the connector through the hole where the sensor wires pass. I decided to cut the sensor wires and use wire connectors to attach the sensor as instructed in the sheet provided with the sensor.

NOTE: You MUST use third party "gray" colored wire connectors that you can purchase in a hardware store. - the connectors provided DO NOT have a metal insert and even after several attempts would not grab the wires.

Another caution is you should use a self-tapping sheet metal screw to fasten the sensor to the oven wall if you encounter the same frozen screw that I did!

After I installed the sensor I tested the oven but found that this DID NOT solve the problem! I needed to order the "hidden" bake element that is mounted under the bottom oven wall and also the broil/bake element that is mounted inside of the oven on the top. See my comments for the Bake Element (bottom)

I broke the glass by hitting it with the edge of a broom

  • Customer: Bernice from Phoenix AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Clean off all broken glass and wipe down the debree,figure what side the glass goes then unscewed the base then the sides then add gorrilla glue on the edges to help set the glass in place had some hold it the screw th center bottom in first then got the sides in place with the bottom rack then screw it all back in to place making sure the side and top were in place right that was it.

MOUTING HOLES DID NOT LINE UP, WIRES HAD A DIFFERANT PLUG THAN ORG.

  • Customer: Charles from Princeton IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
USED NEW DIFFERANT SCREWS TO MOUNT IT AND CUT AND SPLICED THE WIRES TO USE THE ORG. PLUG.

The old panel becamed worped & the finish was distressed.

  • Customer: Mike from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took the old one out and replaced it with the new one, fits perfect.

The old glide broke

  • Customer: Dave from Tampa FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Its was very easy, I unscrewed the old part and screwed on the new one and put the drawer back in place and it works perfect.

Broken drawer glide

  • Customer: karen from Thornton CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Used a phillips head screwdriver to remove the single screw holding the part in place and put the new one on. Finding the part on this site was a breeze and it arrived quickly. A first rate experience all around.

Bad tempature sensor

  • Customer: Art from Parma OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Followed instruction on web site
All Instructions for the 66575775890
76-90 of 95