Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 66575775890

66575775890 Kenmore Range - Overview

Get Parts and Repair Help for 66575775890

If you know the range repair part you need, you can browse the list of all parts on the 66575775890, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for 66575775890 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.96

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$7.36

Rear Drawer Glide

This OEM replacement rear drawer glide supports the storage drawer on your range, and allows the drawer to open and close with ease. If your storage drawer will not open or close, or catches and sticks when you are trying to move it, there could be an issue with the glides. Check the glides and glide channels for any physical damage, and make sure they are properly fastened to the range walls. To complete this quick and easy repair, you will need a Phillips screw driver. Because the drawer has four glides and each are sold separately, make sure to order the correct amount you require.

$31.06

Temperature Sensor

This temperature sensor is used to measure the inside temperature of a self-cleaning oven. Its 1000-ohm resistance increases with temperature. The sensor has male leads, is 6 inche...

$2.96

Screw

This screw is sold individually.

$4.88

SCREW

Sold individually.

$31.67

Light Socket

The light socket on your electric range connects the power source to the light bulb. If your oven light is malfunctioning, you may need to replace the light socket. The light socket is located in the back of your range, so in order to access it you will need to remove the back panel. Many of our customers have rated this repair as easy, and it should take less than 15 minutes. Before you begin this repair, make sure to disconnect the power source from your range. This is an OEM part sourced directly from the manufacturer.

$2.96

Screw

Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an ...

$63.34

Inner Oven Door Glass

This pane of glass is the innermost piece of glass on your oven door. If you notice that the inner door glass on your oven is damaged, you will need to replace it. This part is made entirely of glass. It is approximately 18.5 inches in length and 12.5 inches in width. To complete this repair, it is easiest to remove the entire door from the oven and set it on a more suitable work surface. You will require a small flat blade screwdriver and either a #3 Phillips screwdriver or a #2 square head screwdriver to complete this repair. This is an OEM part sourced directly from the manufacturer. This part is sold individually.

$5.72

Front Drawer Glide

Sold individually.

$39.33

Oven Door Trim Kit

This white oven door trim set contains three pieces: two for the sides of the door and one for the bottom. The screws are sold separately.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 141 of 180 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

Front burner would not light. The igniter was cracked and the spark would not jump to the burner head.

  • Customer: Marilyn from Antioch, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 44 of 44 people found this instruction helpful
I pulled the range from the wall and disconnected the power cord. I removed the grates, burner caps and the burners from the cooktop. Using a plastic putty knife, on either side of the range in the front I pushed the retaining clips to allow the cooktop to be raised. I used a short board to keep the cooktop open. I cut the wire leading to the broken igniter ... read more

surface burner igniter insulation broken, in-op

  • Customer: David from Reedley, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 34 of 39 people found this instruction helpful
Broken ignitor wire had been previously removed to determine part number. Exact length was not availible (37"), but similiar unit (36") (one inch shorter) worked with zero problems. To re-install replacement wire/ignitor, I removed all four grates, and surface burners (allows top surface to pivot upwards.) Raised front of stove top surface by pushing in side... read more