Models > 59673503201 > Instructions

59673503201 Kenmore Freezer - Instructions

All installation instructions for 59673503201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the freezer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 59673503201
601-615 of 810
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Fridge and freezer not cooling

  • Customer: Thomas from Sunrise FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Removed the back panel (6 or seven screws), removed the relay with the capacitor from the compressor (by hand), removed the connector from the relay (with help from a flat head screwdriver), installed the new relay with the new capacitor, closed the back panel. Piece of cake and saved the $450 to $500 estimate to replace the compressor...

Fridge not cooling. No compressor, just lights

  • Customer: Reginald from Berrien Center MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the electrical circuit and noted that both the fan and compressor were powered on a circuit that goes thru the Freezer Thermostat. Lights are on a separate circuit. Since neither the fan motor or the compressor were doing anything, I guessed the problem must be with the Freezer Thermostat. To test this I shorted the Thermostat and the fan and compressor started immediately. I ran the fridge in this mode for a few minutes to determine if it was cooling. When I was satisfied that it was, I ordered the Thermostat. Replacement took only a few minutes using a screwdriver and pliers. Fridge works perfectly now.

Freezer is cold, refrigerator is warm. Coils in freezer section frozen.

  • Customer: Mark from Wellington OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug refrigerator. Remove the food trays in the freezer section. Unplug the wire connector to the icemaker. Remove the three screws to the icemaker then remove the icemaker. To remove the back panel, first remove the plastic cover on the top by inserting a screwdriver in the indicated slots on the sides then prying until cover snaps off. Remove the plastic cover for the temperature probe in the upper right corner by snapping off the cover and carefully fishing the probe through the hole in the cover. Remove the 4 screws in the rear panel and carefully pull panel out from rear of freezer section. Fish the temperature probe through the hole to allow the panel to be removed. Snap the plastic icemaker plug connecter mounting bracket out of rear panel and fish it through the panel. Now the rear panel can be completely removed. Locate the defrost thermostat in the upper section of the freezer compartment and unsnap it from the copper coil. Cut wires to the thermostat, being sure to leave enough length to splice the new thermostat in. Crimp the wires to the new thermostat using a butt connector and heat shrink tubing to seal up the connection. Snap the new thermostat onto the copper tube where the old one was positioned. It is a good idea to check the heater element with an ohmmeter while you have this all apart. Do this by unplugging the element on the right side and connecting one side of your meter to the plug there and the other side of your meter to the plug connection that is on the icemaker plug (trace the wires). If you do not get any continuity, then your element is bad and will need to be replaced. Replace the rear cover after re-installing the plug assemby for the icemaker and temperature probe. Dont forget to fish the icemaker tube and the temperature probe through the rear cover before screwing it back in place. re- install the plastic covers on the rear panel and the temperature probe, then reinstall the icemaker.

iceing up

  • Customer: FLOYD from STARBUCK WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I found the video and write up’s very useful for repairing a newer refrigerator that just ran out of warranty.

Refrigerator did not defrost causing cooling coils to ice up

  • Customer: Bobby from White Plains MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Simply followed the easy to understand instructions supplied with the defrost thermostat.

right side door would pop open when left door closed

  • Customer: zach from nashville TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The right side door of our Jenn Air french door refrigerator would pop open and stay open (just) when the left door was closed. I ordered a new door closure and bushing-d for the door. As it turns out the existing bushing was broken but I replaced both anyway since I was in there. First I removed the plastic hinge cap which is held on by one phillips head screw. Then used a nut driver to remove the hinge itself and pulled the door up and off after removing the internal shelves which pop right off. I laid the door on a blanket on the floor and hung a towel over the opening where the door was to try to save some cool. I pulled out the existing bushing-d and inserted the new one. I replaced the door closure and applied grease, then put the whole thing back together. It works good as new! Doors close properly I wish I had done it sooner!

No Ice do to water fill cup & bearing was damaged

  • Customer: Joseph from Kings Park NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
took off the ice maker, unscrewed the body, replace icemaker shut-off arm, water fill cup & bearing, reconnected the unit & have ice now, Thank you PartSelect

No light in frig

  • Customer: Irene from Whitehall MT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Light switch in the refrigerator was faulty from the first day we installed the fridge.

  • Customer: Mary from Wasilla AK
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

light would come on and off

  • Customer: Dora from Rock Island IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Viewed the viedo - it showed what to do

Switch didn't work

  • Customer: Don from Laramie WY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

ice maker quit making ice

  • Customer: denton from grinnell IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged the refrigerator.Removed the nut on the front bottom side from the support bracket with a nut driver.Pull down and out the old icemaker but not clear out to remove the electrical connector reaching to the back . Re-used the old front cover and the wire support clips and the wire connector assembly.Also put the shut off wire on the new icemaker.Re-installed in reverse sequence and waited for ice cubes to be made.Make sure the water line coming in the back goes to the ice tray.

Ice maker had been leaking for several months and needed replaced

  • Customer: Joe from Leonard TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took the old part out and put the new one in and it works like it should. I loosened two screws and took one screw out with nutdriver. then I used the old wiring harness, bail and cover to finish.

The ice maker had been dripping and than stopped making ice. I worked with it and got it to work again for a few days and than the same problem occured.

  • Customer: Kathleen from Waller TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video on line first. I shut off the power to the refreigerator. I took the one screw out on the bottom of the ice-maker and pushed up on the ice maker. Than I disconnected the power harness inside the refrigerator. I took it out and changed out the harness from the old one to the new one and also the bar that dumps the ice. I reconnectected the harness to the back of the refrigerator, made sure that the water spout lined up correctly. Pushed the ice maker down on the screws and reconnected the screw that I had removed. Waited about 1 hour and had ice cubes. This was an easy process after watching the video.

follow the video that PartSelect has online

  • Customer: Rich from Wickenburg AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watch the video and then do the repair.
All Instructions for the 59673503201
601-615 of 810