Models > 57731H7WW > Instructions

57731H7WW General Electric - Instructions

All installation instructions for 57731H7WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 57731H7WW
31-45 of 397
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer failed to drain water from machine

  • Customer: Kristy from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 10 of 10 people found this instruction helpful
1) Disconnect power
2)remove front panel
3) remove screws and take hoses off
4) remove & replace water pump
:) YAY. all done

Tranny oil ran out onto Laundry room floor/making noise

  • Customer: Larry from House Springs MO
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 11 of 13 people found this instruction helpful
Removed front cover(use screwdriver)clips on top of cover under lid
Disconnected power from wall
Disconnected wires to motor 1 screw/unplug for motor
Uncwrewed clamp on drain hose
Removed top lifts off easliy
With help released Washing drum assy from hangers
Slid back and Tilted drum assy outwards from drum opening out to the front of machine
Pulled agatator up and off of hub
Remove one bolt from hub 1/4 " rachet w 3/8" socket
Pull off cap
Removed Locking nut(couterclockwise)nut is soft metal used good vice grips firmly locked on nut
Removed inner washing drum
Turned over Entire Assy (motor up)
Removed belt (slid off)
Removed 4 blots from Motor/Tranny assy to Plastic outer drum
Lifted off Motor/Tranny assy and pulled tranny out
Reaasemble in reverse order witht the exception of replacing the hub seal(inside)Outer drum assy.
There were service instruction under the front control panel.

Grind noise becoming worse

  • Customer: Eric from Oak Harbor WA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 13 of 19 people found this instruction helpful
Used the repair instruction paper behind the washer control panel and used the online parts diagram. Also the online responces from other customer repairs gave me the idea to take a small pipe wrench (with a sock over the bottom of handle) and tap it with a 10 lb sledge hammer to remove the alumium hub nut. *** It is a backwards threaded nut **** I did not know I was going the wrong way until I looked at the new nut and noticed it's reverse threaded!!! After that it was just taking everything apart and putting it back the way you found it.

Changed drain hose on GE washing machine

  • Customer: Andres from Stamford CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
I attached the Drain Hose Clip to the Drain Hose Extension and then pushed the drain hose all the way into the drain hole in the back of the machine. I then screwed the clip to the machine. Done. Very painless. Fast delivery... ordered it on Monday, arrived on Tuesday.

Excessive agitator side movement

  • Customer: Richard from Spring City PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 11 of 14 people found this instruction helpful
Bought all of the parts to remedy this. It ended up being the top transmission seal/bearing which is not a replaceable part. I could see the shaft moving side to side. But the parts diagrams are not detailed enough to show that when assembled.

She led a good life.

My new side loader is SO MUCH BETTER AND INSANELY EFFICIENT. I highly recommend making the change if you need a transmission..

transmission leaking grease

  • Customer: Dennis from Chilhowie VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench set
  • 10 of 12 people found this instruction helpful
removed front cover the agitater then cover over large nut then large nut then inner tub then split ring and tub bearing then disconnected the hardware around the outer tub then replaced transmission then put back together in reverse order.

Wasing machine strted to make horrible

  • Customer: Roman from Amherst MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 15 of 27 people found this instruction helpful
took it appart and found that the suspension rod was broken. went on line an ordered the parts.
The parts arrived 3 days later. Installed the parts and the washing machine was working within a half hour.

Main seal leaking & burned bearings on & in transmission

  • Customer: Gregory from Mountain Home ID
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 21 of 45 people found this instruction helpful
Outrageous bad design for GE. We bought a SS tub washer but during repair found hidden aluminum components as 'wet' support structures, with massive corrosion; GE's SS tub is a fraud. Main seal went bad after 2 years, washer has a drip pan - no wonder, the problem was hiden for another year while parts burned up. Replacing transmission is basically simple if you have a large hammer and pipe wrench to remove the left hand turn aluminum main holding nut. Replacement parts were okay but we are going to sell washer & dryer immediately because of bad design - it will be a good machine for someone else for a couple years.

Waher would not spin wet clothes.

  • Customer: Gerald L. from Las Cruces NM
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 10 of 12 people found this instruction helpful
Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.

Hose and clip were broken in moving

  • Customer: DARYLD from SCHOFIELD WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
The parts were here in 3 days and the repair went very quickly .Quality item would do business again.

Noticed 3 straps were broken when we replaced the hose

  • Customer: Christine from Tempe AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 9 of 10 people found this instruction helpful
I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!

Washing Machine would not balance on spin cycle

  • Customer: Jarid from Louisville KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 22 people found this instruction helpful
I replaced the work tub dampening strap because that what everyone recommended to replace for this problem. However the purpose of these straps is to dampen the agitation cycle and they have nothing to with the spin cycle at all. the balance ring assembly had been rubbing on the outer tub so I decided to replace it because of a "balance issue". However the ring is liquid with baffles to counter balance the load as it spins and it still had the liquid inside of it so it was actual not needed. What fixed my issue was I found a bolt laying at the bottom of the washer. This bolt was one of the 4 bolts that hold the outer tub to the metal support. When it feel out the tub was only held in at 3 points not the needed 4. This allowed it to rock a bit in the high speed spin and you thought it was going to fly into a 1000 pieces. I replaced the bolt and other parts since I had paid for them and everything works great now.

Washer won't drain water

  • Customer: Ben from Lake Forest CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set, Wrench(Adjustable)
  • 9 of 11 people found this instruction helpful
Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

Purchased used washin machine w/o drain hose

  • Customer: Daniel from Oxford GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

hub corroded away and left spin basket sitting on bottom of tub.

  • Customer: Leda from Port Saint Lucie FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 9 of 12 people found this instruction helpful
Biggest problem was getting old hub nut off. I had to remove it in pieces because it was corroded so bad.

Once hub nut was off it was a breeze to replace the parts after cleaning off the threads and shaft.

Reassembled in reverse order.. and ran.

I have to give accolades to PartSelect.. their customer service is second to none. i ordered the parts just before the Christmas holiday and they shipped them to my door in under 24 hours at no extra charge to see that I got them on time...
THANKS!.. It sure helped.

Would I do business here again.. YEP!

I will recommend you to others.

Thanks.
All Instructions for the 57731H7WW
31-45 of 397