Models > 57731H7WW > Instructions

57731H7WW General Electric - Instructions

All installation instructions for 57731H7WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 57731H7WW
46-60 of 397
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer tub fell sideways

  • Customer: Chris from Tampa FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
Only took 2 days to ship. Took the screws out of the bottom rear panel to gain access to bottom of tub. Next pushed the two hidden tabs with flat screwdriver in the front to gain access to the top of tub, they are located straight inline with each side of the washer lid in seam between the top panel and the front side panel of washer. Then installed the new suspension rod and reassembled. You can find online videos that show how to disassemble appliances if you're not sure how to get them apart for repair. My first appliance repair was easy to do and saved a lot of $$$ vs paying for repair or purchasing a new unit.

Washing Machine would not balance on spin cycle

  • Customer: Jarid from Louisville KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 20 people found this instruction helpful
I replaced the work tub dampening strap because that what everyone recommended to replace for this problem. However the purpose of these straps is to dampen the agitation cycle and they have nothing to with the spin cycle at all. the balance ring assembly had been rubbing on the outer tub so I decided to replace it because of a "balance issue". However the ring is liquid with baffles to counter balance the load as it spins and it still had the liquid inside of it so it was actual not needed. What fixed my issue was I found a bolt laying at the bottom of the washer. This bolt was one of the 4 bolts that hold the outer tub to the metal support. When it feel out the tub was only held in at 3 points not the needed 4. This allowed it to rock a bit in the high speed spin and you thought it was going to fly into a 1000 pieces. I replaced the bolt and other parts since I had paid for them and everything works great now.

the control knob plastic gear was stripped

  • Customer: David L. from London OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
took the needle nose pliers and removed the timer knob clip from the back of the control knob. Removed the control knob and the dial with compression ring. Installed the new dial compression ring and pushed the control knob on. Note: the new control knob comes with the clip allready on the back of the control knob. Took me about 3 minutes to replace.

washer was not agitating

  • Customer: Dwight from Orlando OR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 12 of 25 people found this instruction helpful
First i the four screws on the switch area remover the front panel. Remover the lid swith and replace it. It was good to go again. It is as easy as one two three.

My washer would not drain the water out.

  • Customer: jayme from drummonds TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 6 of 7 people found this instruction helpful
IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

tub fell down on one side

  • Customer: douglas from Stockton CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 10 people found this instruction helpful
after ordering part and getting the wrong part sent to me i was able to finally get right part to my house 2 weeks later, i pulled front cover off with a screwdriver took out broke rod and inserted new part closed cover and hooked power back on and was in business

the bottem of the tub

  • Customer: michael from warwick RI
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 6 of 7 people found this instruction helpful
at the bottom of the tub their is a mettal peace witch holds the tub to the transmision witch is made of zink(aka junk metal or zink+tin)witch broke stoping tub from sping the clotes dry so atfer odering the new part and nut..
and finding out that it is a LEFTHAND nut made of alumanum
taking a small drill bit 1/8" and drilling the nut to weakin it making it brake able then cleaning the treds up
the new part fit right in the tufest part was hold the trans still to get the nut on tightenuf to hold the tub

Inner tub base hub disintegrated

  • Customer: Doug from Kannapolis NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 5 of 5 people found this instruction helpful
I had to take the washer outside since there was no room to work on it in the laundry room. The extra space allowed me to spread out the parts, use the garden hose to clean and have light enough to take digital pics of the wiring before I disconnected them to remove the upper panel.

Removing the upper retaining ring for the tub was simple with only 4 screws. The agitator pulled right up and out. The nut cover/agitator anchor removed easily with one bolt.

The tough part was the inner tub base hub nut that I could not get off. Another user had commented on how they had to chisel the nut off and that was the best advice. I used my air chisel on either side of the nut and it was pretty quick to get off - within 3 min. If I hadn't read that I wouldn't have ordered another nut to replace the one I chiseled off.

The diagrams and repair stories really made the difference. Cleaning and reassembling was done within about an hour - cleaning the 11 years of soap scum at least an hour total before and after replacing the parts.

The zinc drive hub that connects the transmission to the tub had corroded away.

  • Customer: James from Lapeer MI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 6 of 8 people found this instruction helpful
It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

Water was leaking

  • Customer: Christine from Tempe AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 5 people found this instruction helpful
My husband was unavailable and already overloaded, so I took a screw driver and removed the front cover of the washer. After I discovered where the leak was coming from, I used a screw driver to remove one end of the hose and pliers to remove the other end. I went online, found the part and ordered it. It came in surprisingly fast. My husband put it back in about 5 minutes.

Blades broken off agitator

  • Customer: Michael from Itasca IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 17 people found this instruction helpful
Simply put hands, one under each side of the agitaror and pulled up. The part snapped off very easily. I then placed the new part in the tub and pressed down. Extremely easy, should have done it sooner!

Washer would not spin

  • Customer: Rick from Ephrata PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.

There was no fabric softener dispenser

  • Customer: Gigi from Monroeville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.

washer loss balance

  • Customer: james from sidney OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 11 people found this instruction helpful
went very well thank you

Water was leaking from machine.

  • Customer: RUPESH from BELLFLOWER CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pump on Sunday and leak was gone and wife was happy.

------Got chicken and beer that Sunday--------------
All Instructions for the 57731H7WW
46-60 of 397