Models > 4875 > Instructions

4875 Jenn-Air Range - Instructions

All installation instructions for 4875 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4875
31-45 of 112
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Grease filter needed replacing

  • Customer: Freda from Elizabethtown NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
Remove old filter- put in new filter. EASY!!!!!!!!

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 7 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Oven would not heat at bottom

  • Customer: Wayne from Conifer CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I did a continuity test and determined the old element was bad - ordered the new one and put back the screws. All done!

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Rear burner always high, ignored temperature setting.

  • Customer: Dana from Chapel Hill NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
Turned off breaker for range. Removed 4 phillips screws on control panel, tipped it forward and rested it on top of partially open oven door. Removed knob and nut on old switch. Moved wires, one at a time from old to new switch. Put new switch in place, tightened nut and pushed on knob. Put control panel back in place and installed 4 screws... piece of cake.

I destroyed my grease filter in the Dishwasher and it just about disintergrated.

  • Customer: Rosetta R. from Jamaica Plain MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I just had to drop the grease filter into the slot. IT took less than a second. BUT what I am really pleased with is that it took less than a day and a half to get the part. I ordered it on Thursday Morning. It was shipped on Thursday Afternoon and In my driveway by Friday NOON!!! WOW!!! How great was that!!!!!! The fastest service I've every had for ANYTHING!! BRAVO!!!!!!!! to all your workers!!!!! rrm

burner would not get hot

  • Customer: Royal from Gilmer TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
removed two screws thenpulled element up unpluged wires

lost one of the knobs

  • Customer: Sabra from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Ordering and installing was easy. The hardest part was getting the exact match to 20 yr. old appliance knobs. First one I ordered had wrong shaft hole, but it matched perfectly in design. Decided to reorder and just replace all four with matching new-style knobs and the correct shaft hole. Yeah. Looks great and REALLY easy to install.

surface switch was bad

  • Customer: Arthur H from Irving TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 1 of 2 people found this instruction helpful
just swapped out the two switches

knobs were getting hard to read.

  • Customer: Dave from Bloomingburg NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Pulled old knobs off, pressed new ones on. Probably well under a minute for 6 knobs. Anyone with the IQ of a horseradish could have done it. But what was really great was the help and personality of the agent at the other end of the phone. Shipping was as promised, and the entire experience was delightful!

Element in oven burned out

  • Customer: Eric from Bliss NY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I had to use a mirror and flashlights to see in the back of the oven to replace the screws in the new element. It was very close quarters and difficult to see behind element plate.

old nkobs old and discolored

  • Customer: WALTER from EL CAJON CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
took old knobs off replaced in 3 minutes

COULD NOT USE ONE BURNER

  • Customer: Anne from Bedford Hills, NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
TURNED POWER TO STOVE OFF. REMOVED TWO SCREWS FROM COVER - LIFTED COVER UP AND PULLED SWITCH OUT AND DISCONNECTED WIRES. PUT NEW SWITCH IN AND CONNECTED WIRES. MADE SURE THAT IT WAS IN CORRECT POSITION BY PLACING KNOB ON TO MAKE SURE OFF POSITION WAS CORRECT - THEN PLACED PLATE IN POSITION AND CLOSED - PUT TWO SCREWS BACK ON PLATE AND PUT NEW KNOB ON. TURNED POWER BACK ON AND TURNED KNOB AND BURNER BACK IN OPERATION

The contacts on my convertible range top were corroded

  • Customer: Kurt from Salem NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 26 people found this instruction helpful
I ordered the kit that contained all 4 wires and contacts. The replacement was fairly easy. The only drawback was the tight quarters in running the wires. The job was quick and a success. Now I can use my right side of my stovetop again!

Old Stove Top

  • Customer: Robert A from Farmington ` CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Ordered new cartridges
All Instructions for the 4875
31-45 of 112