Models > 41748102701 > Instructions

41748102701 Kenmore Washer - Instructions

All installation instructions for 41748102701 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 41748102701
76-90 of 221
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer would not spin

  • Customer: Robb from North Huntingdon PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 1 of 1 people found this instruction helpful
Removed old shock abs. (both sides). The one side, I had to remove the speed control board to access the lower nut on the one shock. Install was fairly easy however, it did not fix the washer. Apparently there was something else (either a switch, the control board or the motor) needs replaced too.

washer door woild not lock and would not allow washer to operate

  • Customer: Kevin from Merrimack NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Removed top cover of washer to get to the door lock mechanism then used a phillips head screwdriver to remove door lock mechanism. I then replaced door lock mechanism with the new one I bought from PartsSelect. The repair job was very easy and took a total of 15 minutes to remove old part and install new one.

Loud humming noise from the door closure area.

  • Customer: Alyre from Van Buren ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
First,turned the power and water off. I disassembled the door lock and switch assembly by removing two screws from the rear of the top lid to gain access to the switch. Removed two screws from the switch assembly located in the front door latch area. With screws removed, I seperated the three terminal blocks and inspected the assembly for failure potential. Discovered a small crack in the switch housing which created error in relay function. Ordered the part and installed in reverse order of above. Realigned the door for proper closing, turned water and power on and did laundry all night to catch up!!!

Washer would not complete the spin cycle

  • Customer: Andrew from Fruitland ID
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.

Broken shock

  • Customer: Ron from Blaine WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

washer drained withn no spin

  • Customer: William from Lancaster CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Remove top of washer, remove door lock assembly,install new assembly replace top.

Washer would spin in any cycle

  • Customer: Cheryl from Brandon FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Tilted the washer back to take the 2 screws off the bottom to remove bottom plate. Took the 2 nut screws from the bottom of the face plate so that the front of the washer would pull slightly out from the bottom. Removed the 2 screws from the door stricker plate which allowed the door lock assembly to come out through the side of the washer. Unplugged 3 plugs, plugged the new switch in and slid it back into place, put the 2 screws back in to hold it. Reattached the front and the bottom plate. And bingo done. It worked and saved us about $245.00. Very happy!!!

$500 Repair for $25, well worth the struggle!

  • Customer: beverly from Miami FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 1 of 2 people found this instruction helpful
I replaced both shock absorbers that hold the drum on a front loading washer. They both snapped at the base and have since been replaced by a different style shock absorber. There are 2 pins that hold each part in place. I took 5 minutes to replace 3 pins and about an hour to replace the last one, which was in a very tight spot. After much sweating and swearing, I managed to get the pin back in. Was it worth it? ABSOLUTELY! Partsselect.com is a dream for straightforward repairs. This is the second repair I have done on this machine (which is less than 5 years old) and both repairs have cost less than $30.

Bouncing washing machine

  • Customer: anthony from Florence AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 1 of 2 people found this instruction helpful
The instructions that came with the new shock absorbers were very detailed and walked me through the repair step by step. The new shock absorbers are much better quality than the old tube style shocks.

worn out vibration/shock absorbers

  • Customer: W R from Venice FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers
  • 1 of 2 people found this instruction helpful
"Instructions" with the kit suggest pulling the pins out with a pair of pliers. That's fine if you're a gorilla. It's easier to use a 13MM boxed-end wrench. Slip it over the tapered end to depress the locking tab; then tap a 3/8 dowel rod held against the tapered end to remove the pin. Also my washer has a drain tube that has to be disconnected to get access to the top pin. If I had to do this again it would take about an hour.

Washing machine wouldn't go into final spin.

  • Customer: Manny from Old Bridge NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
First unplug the machine, then remove two srews on the back of the machine for the top cover. Remove top cover and then remove two srews that hold the door locking part. Put your hand in the machine and grab the part. unplug the three wire harnessess then plug them back and put back in place and put the two srews back and then the top cover and two srews as well.

Broken washer Drum Vane

  • Customer: KAS from LYNNWOOD WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I follow the instruction that comes with the part.The only thing different is i use WD-40 , to slide the vane better.

Drum was banging around when spooling up and slowing down

  • Customer: Matthew from Pullman WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
The front lower access panel pops off with two Philips head screws. From there, the white pins holding the hold broken shock absorbers can be removed by pressing their locking tab down and pushing them free of the bushing.

After pulling the old, broken items out, the new ones are reinstalled the same way: place the metal end towards the drum, push the white pin through the bushing (only one way is correct) and you're almost done. Reinstall the front panel and get back to having a quiet washing machine!

Machine bounced all over the room

  • Customer: Stuart from Canton MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
I followed the great instructions provided on the site and had the old broken struts out in no time. The new ones went in without a hitch and the time it took me to unscrew and rescrew in the back of the machine was longer than the time it took me to replace the broken parts.

Bouncing and noisy washer

  • Customer: Chad Trainum from Albuquerque NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
I had read the instructions and suggestions on the site. The product arrived with a good set of instructions. I used the deep socket to push in the "catch" on the pins. Once the catch is depressed I pulled and twisted a bit to get the pins out. After I pulled both broken shocks out I replaced them as instructed. I did use a long wooden dowel to get the pins all the way in. Read the instructions and follow what they tell you and it'll be done in under 15 min.
All Instructions for the 41748102701
76-90 of 221