Models > 41748102701 > Instructions

41748102701 Kenmore Washer - Instructions

All installation instructions for 41748102701 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 41748102701
61-75 of 221
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer would function for 2 to 3 minutes and then pause. "PAU" appearing on the display.

  • Customer: Stephen from Amarillo TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Apparently the faulty switch was causing the washer to think that the door was open which would pause the wash cycle. The temporary fix was to disconnect/reconnect the door lock/switch assembly, thereby resetting the switch. Eventually though, the switch had to be replaced. The repair was simple. Unplug washer from power. Remove the metal band and spring from around the perimeter of the door seal. (I had to use needle-nose pliers for this step). Loosen the rubber seal near the door latch area only. Remove old latch by unscrewing the two screws, and disconnect all wired connections. Reconnect wired connectors using the new part and screw back on to the washer using the two screws. Reseat the rubber door seal and hold in place using the metal ring and spring you removed in the first step. Plug washer back in to power. That's it.

Washer wouldn't enter the spin cycle. Clothes wet at end of wash cycle.

  • Customer: Leslie from Tolland CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Open the door. Pull the clamp off of the boot (locate spring at bottom). Peel back the boot on the right side so that you can get to the door lock and switch assy. Remove the 2 screws in the front that hold in the door lock and switch assy. Remove the wires from the old assy. Transfer the wires to the new assy. Screw in the new assy. Refit the boot and clamp. give it a try.

One of the wash tub shock absorbers broke.

  • Customer: Joshuah from Indianapolis IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
I heard that the repair job was simple and the part was not expensive (whew!) The repair video on your website was MOST helpful and gave me confidence. At first I tried it exactly as the guy demonstrated and all went well removing the broken support. Installing the new one (on the right side) was impossible for me. I could not get good enough leverage to fully re-insert the lock pins and I was slicing up my arm on the sharp metal edges. I removed the 900+ screws (just kidding- but there were quite a few) from the back panel and could access the lock pins MUCH easier. All four for both shock absorbers snapped right in. Re-attaching the rubber vent hose involved a few cuss words but I got it back on correctly after taking a break. All is great with the little washing machine once again! Thank you for the installation video and amazingly fast shipping, wow.

belt was still on washer, had developed a loose tear

  • Customer: jeffrey from mount juliet TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Very easy to replace belt on this model, belt had spilt and the loose rubber was flopping around and dislodged plug from water pump. Washer would not start cycle, display showed (no spin). Removed back access panel with screwdriver. Spin the pulley and slip belt off pulleys. New belt is very tight but it will go on, no tension adjustment on this model. Thanks part select quick service will order again from this company.

excessive vibration

  • Customer: Jon from Holland MI
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 2 of 2 people found this instruction helpful
I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.

Drum vane broke

  • Customer: Robert from Boyertown PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
The part ordering and arrival was very easy and fast. Problem with the directions on removing the damaged drum vane. They were not clear directions. Once I figured out what needed to be done it went easy

i broke the soap dispenser on my washer

  • Customer: GLENN from MADISON IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 9 people found this instruction helpful
love parts select have used them several times for parts great company

The plastic door strike/catch had become brittle and broken off inside the door on a front loading washer.

  • Customer: Barbara from Lutz FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
There were only two screws that held the door strike/catch in place. I had to fish out the broken plastic piece with a pair of hemostats. The only difficult part about changing the new piece was that I had to find someone with the correct screwdriver to use since it was not a standara screwdriver. Luckily I live next door to a mechanic and borrowed his. The two screws came off easilty and I was able to replace it in 2 minutes. I was thrilled that the part that I ordered arrived the next day.

Vane broke off inside drum

  • Customer: Glen from Redondo Beach CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 9 people found this instruction helpful
Inserted new vane into slots in the drum. I then held the front of the drum while I slid the vane tabs in place by pushing the vane to the back of the drum. Once the vane was in place, I screwed in the screw that came inside the vane kit.

Wouldn't start

  • Customer: Anne from Storrs CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
With the help of PartSelect's diagnosting tool it was easy to find the right part. The part arrived very fast and the installation was "child's play" by following PartSelect's video. I must have saved > $100. Thank You very much. -Anna-

the latch broke

  • Customer: Sarah from Gilford NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
It was very easy. I simply unscrewed the 2 screws set the new latch into place and replaced the screws.

WASHER DOOR WOULDN'T LOCK

  • Customer: Shawn from Springdale AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 3 of 6 people found this instruction helpful
I WATCHED THE U-TUBE VIDEO AND FOLLOWED WHAT HE DID AND IT WAS FIXED. REASON IT TOOK OVER 15 MIN I HAD TO FIND THE CORRECT BIT FOR THE SCREW. I THINK YOUR WEB SITE IS GREAT
THANKS

Washer would not complete the spin cycle

  • Customer: Andrew from Fruitland ID
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
I started by removing the two screws at the back of the washer and taking the top off of the washing machine. Than I removed the two screws securing the door lok and switch assembly. I disconected the two or three electrical connections and install the new one in the reverse order.

Broken shock

  • Customer: Ron from Blaine WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
As others have mentioned, it was pretty straight forward although a bit finicky to get into the tight spots to press out the pins. The little piece of 1x4 block helped press the pins back in. For the right side shock, I had to undo the large rubber hose at the bottom of the drum and also had to remove the sheet metal shield in the back to allow clearance for the pin to come out. There's only 2 screws holding it in so again, not too hard to do.

broken shock

  • Customer: John from Glennallen AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
removed front panel and used deep socket to remove pins that hold shocks. front left shock took most of the time because of hoses and a unit in the back that needed to be released to be able to remove the pin on the bottom. the right shock was a piece of cake to replace. used a hammer to pull the pins into place (i did not use it to tap on them ) . lots of bloddy fingers from sharp edges.
All Instructions for the 41748102701
61-75 of 221