Models > 41748102701 > Instructions

41748102701 Kenmore Washer - Instructions

All installation instructions for 41748102701 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 41748102701
46-60 of 221
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer will fill and drain but will not spin or agitate

  • Customer: Gabriel from MERRILL WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
Went by the percentage of people with same problem- door switch was the highest. Ordered door switch and a new belt (belt was getting worn- 6 yrs. old) Door switch did not fix problem. Saw on website that it could be motor control board. Took motor control board out. Nothing visible wrong with anything. Decided not to spend $$ on new board. Figured new washer would be better. Put motor control board back in and tried it......works like new! Must have been a loose wire on the motor control board. Next time I will check wires first. :) Getting motor control board in and out was time consuming but no too hard.

Door latch broken

  • Customer: Steven from Pompton Lakes NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 10 people found this instruction helpful
It was done in five minutes! Piece of cake. I will definetly use your site in the future. We had a servir=ce plan with Sears. They are the worst ever...do not pay the money. You only get India for customer service, and they tell you they are coming, do not show, and when you call them they say there is no service tech in the area. You can not get to anyone who can help it theyu did not show twice! We ended up canceling the service, and to their credit they send us a refund. Funny thing about it, they showed up today and left a message on our door that noone answered...this is after they refunded us.

Door strike broke

  • Customer: Chris from Vernon Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
The store I bought the washer from was going to charge $150 service call and over $60 for the part. I searched on the internet and found what i needed at partselect.com. The part was under $7 and the shipping cost more than the actual part. 2 screws, 1 screwdriver and it was fixed. Thanks!

Quickly fixed a dumb mistake.

  • Customer: Andrew from McFarland WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
After accidentally dropping a crystal clock (don't ask) near the open door of the front-loading washer, the plastic striker broke and couldn't be repaired. Without this part being functional, the washer won't start because the door can't be secured.

I ordered the new part, and it arrived quickly -- that's really the story here.

Replacing it meant removing two screws, pulling the damaged part off, slapping the new part in, and replacing the screws. My 4th grade daughter could have done this one -- wish they were all that easy!

I'm glad the part came so quickly. With a local supplier, it would have taken four more days.

drum vanes broke

  • Customer: vernon from middlebourne WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 11 people found this instruction helpful
placed small plillips screwdriver in center hole of old vane and pulled vane toward front of washer and lifted up out of slots. (You need to press down tabs in center of drum slot to insert new ones) Placed new vane at front of slot and squeezed togeather so both sides went in slots and with screwdriver in center hole of vane pushed to rear of washer till vane locked. Incerted screw that came with kit to hold in place DONE.

Original glass broke due to uneven load and drum struck the glass

  • Customer: Dallas from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.

Broken Face Clips on dispenser drawer

  • Customer: david from spring hill FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
I unclipped the old drawer parts from the broken drawer and replaced the old parts onto the new drawer and slid the whole drawer back in the washing machine. It took longer to type this that it did to repair the washer. No tools needed at all.

a busted door striker

  • Customer: mark from Watertown SD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
2 screws off and put new striker in and replaced the screws

One of the wash tub shock absorbers broke.

  • Customer: Joshuah from Indianapolis IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
I heard that the repair job was simple and the part was not expensive (whew!) The repair video on your website was MOST helpful and gave me confidence. At first I tried it exactly as the guy demonstrated and all went well removing the broken support. Installing the new one (on the right side) was impossible for me. I could not get good enough leverage to fully re-insert the lock pins and I was slicing up my arm on the sharp metal edges. I removed the 900+ screws (just kidding- but there were quite a few) from the back panel and could access the lock pins MUCH easier. All four for both shock absorbers snapped right in. Re-attaching the rubber vent hose involved a few cuss words but I got it back on correctly after taking a break. All is great with the little washing machine once again! Thank you for the installation video and amazingly fast shipping, wow.

Door strike on front load washing machine broke.

  • Customer: Jim from Anna TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
PartSelect had the part in stock, shipped that day. The part was delivered the next day, my wife had it installed and working when I got home from work.

Washer would function for 2 to 3 minutes and then pause. "PAU" appearing on the display.

  • Customer: Stephen from Amarillo TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
Apparently the faulty switch was causing the washer to think that the door was open which would pause the wash cycle. The temporary fix was to disconnect/reconnect the door lock/switch assembly, thereby resetting the switch. Eventually though, the switch had to be replaced. The repair was simple. Unplug washer from power. Remove the metal band and spring from around the perimeter of the door seal. (I had to use needle-nose pliers for this step). Loosen the rubber seal near the door latch area only. Remove old latch by unscrewing the two screws, and disconnect all wired connections. Reconnect wired connectors using the new part and screw back on to the washer using the two screws. Reseat the rubber door seal and hold in place using the metal ring and spring you removed in the first step. Plug washer back in to power. That's it.

washer door woild not lock and would not allow washer to operate

  • Customer: Kevin from Merrimack NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Removed top cover of washer to get to the door lock mechanism then used a phillips head screwdriver to remove door lock mechanism. I then replaced door lock mechanism with the new one I bought from PartsSelect. The repair job was very easy and took a total of 15 minutes to remove old part and install new one.

excessive vibration

  • Customer: Jon from Holland MI
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 2 of 2 people found this instruction helpful
I followed the instalation instructions provided with new parts. Getting the mounting pins out was relatively easy However, the shock on the right, behind the pump, was a bit more difficult to remove than the one on the left. I took the rubber drain off the pump in order to get at the pin behind the pump. The new replacement shocks came with the plastic bushings inserted in the shocks in alternate directions. The original pins were all inserted into the bracket / shocks from the rear so when I installed the new shocks I reinserted one bushing on each shock so they we both oriented in the same direction. The instruction says to be sure the mounting pin is pressed from the side with the busing collar. It seemed strange the shocks came that way, with no mention of switching them. The most difficult part on the installation was pushing the pins back through the bracket and shock since there was no easy way to push the pins in from the rear. I used a large channel locks on the left side, but the right side was more difficult with all of the obstructions. I finally was able to push in place with my bare hands but was very difficult. Sorry to say the new shocks did not cure the vibration at all. I was very careful to make sure the machine is level. I'm not sure if there is a cure other than replacing the machine.

Drum vane broke

  • Customer: Robert from Boyertown PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
The part ordering and arrival was very easy and fast. Problem with the directions on removing the damaged drum vane. They were not clear directions. Once I figured out what needed to be done it went easy

Both shock absorbers for the tumbler had broken off

  • Customer: Elizabeth from Bellevue WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 2 of 2 people found this instruction helpful
The repair itself was simple; it was the original design of the washer itself that made it time-consuming, because of the tight spaces involved. Basically, all you have to do is remove 2 plastic pins, take out the broken part, make sure you have the new part facing the right way, and put the 2 plastic pins back in. Should take 2 minutes if there are not other machine parts in the way!
All Instructions for the 41748102701
46-60 of 221