3ZAED4475TQ0 Admiral Dryer - Instructions

video on your website made it super easy

This is a straightforward repair that you can do in an hour or less. Open the lint trap and remove the two screws. Use a screwdriver to pop up the top of the dryer. Remove two screws that attach the front panel. Now you can lift out the drum and then lift off the front panel. Clean out all the lint. Make sure the motor pulley turns smoothly. Tilt back the dryer diagonally to make the rest go easier. Loop the new belt around the drum (rubber side down) and reinstall the drum against the back wall of the dryer. Make sure the cloth liner fits perfectly around the ridge, with no folds so the drum rotates easily. Make sure the drum fits smoothly against the two rubber positioning wheels on the back wall. Position the new belt around the center of the drum. On the dryer floor, stand up the tensioner bracket. Tricky part -- thread the belt so it runs through the bracket and loops around the drive pulley on the motor, rubber side against the pulley. The belt should be tight, held by the tensioner. Reinstall the front panel so the opening aligns with the drum opening. Drop the top down, snap into place.and reattach the screws in the lint trap. Done!

watched the video on part select.com was a very easy job whenever you had someone showing you what needed to be done,thanks for the help and great customer service.

Just follow the video by Parts Select., The repair is really easy.

Power off by removing plug from wall outlet. Remove two Phillips screws under lint screen filter door. (careful you don't drop them down the filter housing) Pry upper lid loose at both front corners and elevate and retain the lid vertically. Separate old 3 wire switch connector splice halves at upper right housing corner. Remove two Phillips screws at upper right corner of outer front doorway which hold switch. Install new switch with those two screws. Re-connect the connector splice halves; they are keyed for one direction. Close down lid. Plug in power cord.

Per video demonstration offered in web. Very simple. Thanks for your help.

Video showed 3 ways to remove the top section to access the switch. None of which worked on my unit. Instead there were 4 screws on the rear section of the control panel that had to be removed and then lift it past the top of unit to slide forward to remove top to access the switch after that all was the same as video.

turned off circuit breaker to dryer. pulled out from wall and turned.had to remove vent tube to facilitate moving the unit.took off back panel with socket.popped connecting wires off old hi-limit thermostat. took off old hi-limit thermostat, put on new one.reattached connecting wires.(they clip in and out.) screwed back panel on.turned unit back into position, popping vent tube back into unit.flipped circuit breaker back on.IT WORKED! didn't need to replace thermal cut-off, that was still working, but came in a kit with the thermostat.the worst part was diagnosing the problem and figuring out how to use the multi-function meter i had on hand.such a good feeling to fix it yourself and pretty inexpensively!part arrived 2 days after ordered!helpful to have 2 people to move dryer,hold pieces,hold back panel in place when reattaching.but could be done by one person.

Removed power (un plugged), removed two screws on back top of cover allow top to lift up on installed holders., used screw driver at right front and left front to push in the locks on the plastic holders and lifted top and held up with board. Removed two screws holding the switch and disconnect it from the connector and installed the new switch, and connected to connector back up, removed board, lowered top aligned with the two alignment clips and pressed down to lock in place. Replaced the two screw removed from back, plugged back in the power and test the repair.

The online vidio was very helpfull

replacer upper heat themo

Unplugged the power cord. Removed two screws on lint vent , used putty knife to release clips to raise top at front of unit. Disconnected the plug from front door switch. Laid dryer on its back. Removed two screws to remove front including the door. Vacuumed lint from inside unit. Installed belt temporarily using two pieces of masking tape to hold it in place while properly routing the belt. Gave the tub a full turn to insure alignment.. Reinstalled the front of unit with the two screws. Righted the unit and snapped down the top. Replaced the two lint vent screws. Plugged it back in and done! Piece of cake!

Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

I unplugged the dyer remove the back and took out the part and replaced it with the new one done !Thanks to your video I watch on the enternet.thank you so much

Follow your instructions. Thank You