3RMED4905TW0 Maytag Dryer - Instructions

After getting the part and sizing up what to do. I removed the 6 1/4 hex nuts from the back. I removed the 2 hinge nuts 3/8 and popped the lid of the dryer up. It wasn't coming up all the way. I removed the lint filter and removed the two #1 Phillips screws that held the lid to the duct and it came up easy.The switch itself was clipped together and came apart with ease. 2 #1 Phillips screws held the switch in place and quickly tightened down the new switch. I clipped the new switch to the old lead and just reversed the order putting it back together. The light worked and the drum stopped when the door was opened during the cycle. The part matched perfectly and there was no guess work about clearance. It was an easy repair.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

I took out the old worn out part and replaced with the one I order.

I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.

I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.

I followed directions found on several similar YouTube videos since the instructions included in the Whirlpool parts kit were not for my model dryer. I found that the original idler pulley was not rotating and the belt had worn a groove through it. I replaced all 4 roller wheels, idler pulley and the belt. Problem solved.

Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulley lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck

replaced dryer lint screen with new.

first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

pull the back off and replace the pulley.

Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.

Installed new door switch, so, so simple. Unplug dryer, remove lint screen, undo 2 scews located at base of lint screen opening. Use flat head screw driver to pry up dryer top, once open, rest the top against the wall. Now you will see the door switch in the right hand corner at front of the dryer.Open the dryer door , remove 2 screws holding the broken switch, disconnect wire from dryer, click in the new switch, put everything back together, plug in the dryer and go! Super quick and easy, wish I had just done this months ago!!!!