3RMED4905TW0 Maytag Dryer - Instructions

This problem occurred Thursday afternoon; after I took out a load of dry clothes, it wouldn't restart. I realized that the switch was busted, it used to click but it was just hanging. Watched the video and ordered it right away. It arrived Saturday morning via Fedex and I installed it in about 5 minutes. It probably took longer to watch the video. 23 bucks and the dryer's running perfectly. I've replaced several parts this way on my appliances, always feels good to do it yourself. Good as new.

Took old one out and put new one in. Popped the top off and took out two screws. That was it.

YouTube.

we followed your instructions on the video and saved over $500 on a new dryer. Thank you The Dean's

UNPLUG the dryer first. Remove lint filter. Unscrew dryer top from lint filter compartment. Pry top of dryer loose under the front edge, using a flathead screwdriver. Prop open so you can see into dryer where the drum sits. Open dryer door, and on right side, unscrew the door switch. Pull the old switch loose from the three wires leading into the plastic connector. Connect the new switch and reattach everything in the opposite order you took it apart.

My husband simply changed the switch and now I could'nt be happier. Thank you for sending the switch so quickly!

Very simple. First, unplug the dryer. Unscrew the 2 screws that hold the lint screen in place and remove the lint screen. Now comes the only complicated part. The video recommends using a putty knife to get the top of the dryer to open. I recommend plastic wedges (you can buy one for less than $1 at a local hardware store; I used 2) because then you will not damage the aluminum, which is very easy to do. Basically you put the wedges (I used two) into the opening and hit then very gently with a hammer and they force the top of the dryer to open. From there you remove the 2 screws that hold the switch in place, unplug the switch (this may take a little bit of effort), plug the new one in, put the screws back in place, put the top back on, screw the lint screen screws back in, put the lint screen back, plug the dryer in and you're good to go. This took all of 10 minutes

The repair was simple. The plug must be pried away from the connection with a pocket knife or small flathead scew driver.

Followed the video and it was perfect. Easy repair that took under 15 minutes. Great, clear process that was perfectly easy.

I followed the you tube instructions. Unplugged the dryer. Removed the lint screen. Unscrewed 2 screws. Used puttty knife to open the top of dryer. Located the door switch and unplugged it and replaced with new part. Closed top. Replaced two screws and put lint filter back in. Plugged dryer in and turned it on. It worked like new. I'm a woman and this is second part I've had to replace on this dryer. Watch you tube video.

followed the very handy installation video. it was easy to repair the door switch as the drum did not stop when it was opened. glad we used your service and would certainly use it again if needed for other items. your prompt attention to shipping was also appreciated. thank you!

I followed the accurate video. I'm sure I saved a lot of money over having a repair man come out. Now maybe my wife will believe that I am capable of repairing some things myself... eh, probably not.

Did as your video instruction. To me the order of work needs attention: Remove the switch, unscrew 1st, then remove the hook and wire connection. Installation: connect the wire first, then hook to the frame, the last step is screw in the switch. That should prevent accident dropping the switch inside the dryer.

The videos on replacing the switch mentioned using a putty knife to pop the top of the dryer open. My dryer is around 10 years old, so a putty knife wasn't strong enough to pop the dryer top off of the clips. Instead, I had to gently stick a flat head screwdriver and twist just to the side of each clip. Other than that, the video instructions were spot-on on for replacing the switch: UNPLUG THE DRYER FIRST > remove the lint collector > remove the two screws from the top of the lint collector's slot with a Phillips screwdriver > pop the top of the dryer up gently with a flat head screwdriver (or a putty knife, if that works for you) > remove the two screws holding the switch onto the front of the dryer (it would be good to notate which direction the switch is pointing) > use a flat head screwdriver to pry the faulty switch's clip off of the dryer's wiring harness clip. Then reverse the procedure with the new switch: plug the new switch into the dryer's wiring harness > screw the new switch into the slot on the front of the dryer, making sure that it's oriented in the correct direction with the switch's arm pointing away from the dryer > lower the top of the dryer back down and press it onto the clips > screw the screws back into the lint collection slot > replace the lint collector > plug the dryer back in > test the dryer.

Putty knife was not enough for me I had to use a flat head screw driver to open the dryer. I had difficulty getting the old switch off had to use a flat head screw driver and needle nose pliers to get it off. New switch went on and the closing of the dryer was a breeze.