36508L Amana Refrigerator - Instructions

Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

Followed your internet instructions. Saved $1200!!

I unplugged the refrigerator and defrosted the freezer. I removed the plastic grate on the front bottom of the refrigerator and removed the plate covering the defrost timer using a nut driver. I used pliers to unplug the defrost timer. Using the Instant Repairman troubleshooting instructions from partselect.com, I used a multi-tester to determine that the current defrost timer was bad. I ordered a new one from partselect.com and and received it very quickly. I plugged in the new defrost timer and screwed it back in place. I replaced the grate, plugged the refrigerator back in. It's been a week and everything is working perfectly! Easy peasy.

remove right door replace lower door cam

Logged in to internet, for whatever reason I selected your site. Good choice! Entered the model number and selected the symtems identical to my refrig. Ordered the recommended parts, (Relay and Start Capacitor), to solve the problem. Reviewed the remove and install video. Received parts as promised by del date. Installed parts under 15 minutes, Frig kicked in and frig has been working beautiful. Avoided all those added expenses of; home service check, amount of days in- shop repair, plus parts and overhead charges. Will recommend site to my friends.

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Since I had more than one issue, I decided to replace the entire ice maker. All I needed was a nut driver and it took 5 minutes. Three hex screws and unplug the wire harness and the whole unit came out. I changed the harness over and installed the new unit. I left for work and came home to ICE. It was Great!!!

initial research suggested that relay is common failure point -opened back panel and found that relay was "truly smoked" - black soot came out when I removed it and shook it also checked that the compressor itself wasnt damaged using the resistance check across pins and also from pin to outer cover - determined that the compressor seemed OK and fault likely isolated to relay - - overload cap seemed to be ok - but decided to replace entire unit (relay and cap) - ordered on partselect.com - video showing how easy repair was very helpful - replaced it - and DONE!

1. Viewed the video furnished (very helpful) 2. Turned off circuit breaker (avoids having to move the refrigerator), took my chances and left the water on 3. Removed the ice bin 4. Removed bottom retention screw, loosened the top two screws 5. Lifted the old ice maker free of top two screws 6. Used the bright flashlight to see how to release the rear electrical connection 7. Placed old unit on toweling, removed the electrical harness, the bail and the lower retention offset bracket (needed because the Kenmore's bottom retention is toward the center of the ice maker) and reinstalled them on new unit, taking care to maintain the original harness clip method 8. Carried the new unit to the refrig and installed the rear harness connector, then lifted it to mount on the top screws, forced it down to correct position, installed lower screw and tightened all three. 9. Placed bail in 'Operate' position, Installed bin and turned on the power. 10. Next morning, success!

I watched the installation video posted on PartSelect website, which really helped to know what to do and to avoid unnecessary missteps. Although the door closes, but the new gasket doesn't have the force of suction when opening it, which led me feel suspicious whether the door is closed completely.

be sure the power cable is NOT plugged into an electrical outlet - removed the cover on the bottom rear of the refrigerator - using a flat blade screw driver pry the cover off the side of the compressor - remove the old relay - remove the wires from the old relay and install them on the new relay in the same location - install the new relay on the compressor connections - snap the cover back on the compressor - replace the cover - power the refrigerator on - the compressor should start and run normally

Called amana repair to install new part , but worker called in sick. did it myself, was easy, only one phillips head screw and part slid out. looks like a florescent light starter with a wire attached with a loop on the end.very easy and thanks to the super fast delivery..next day, i could hardly believe it...

You just take the back panel off (8 screws with hex heads), disconnect one wire harness, pull off the relay, and push on the new one. Easy peasy. Getting the wires off was the only tricky part, they clip in place so you have to pry the retaining clip loose. Unfortunately, it turns out our compressor is shot so replacing the relay did not fix the problem.

My 8 year old Maytag side-by-side started having a buzzing sound coming from the compressor area that lasted around 8 to 10 seconds which was followed by a "click" sound. It would repeat every 3 minutes or so. From what I read, the Overload/Relay with Start Capacitor was the likely culprit. I got it replaced tonight but unfortunately, the same problem is occurring. The downside is I likely have a bad compressor (not worth replacing after cost of parts and labor) and wasted $60 on the Overload/Relay with Start Capacitor. Partselect's service though I would say is top notch. I received the part within two days of placing the order and my order confirmation email even had a link to a youtube video detailing the installation. That was very helpful. I just wish I was looking at a $60 fix vs a grand for a new fridge! Oh well, live and learn....and no more Maytag.

Once I received the new icemaker, I removed the old one by loosening the two upper screws and removing the lower. The wire connector came out easily. The wire and the bale from the old unit had to be transferred to the new unit. Then the new unit was reinstalled and the wire plugged back in. It took several hours for the cubes to begin dropping.