36058 Refrigerator - Instructions

This refrigerator has the freezer on the bottom. You have to remove both of the drawers to get to the icemakeer. I did not disconnect the water line or the power to the unit because it is a hassle to pull the unit out of the hole where it resides. I first unplugged the power from the icemaker to the unit and used a flat tip screwdriver to get the icemaker out. The old one was gross. We had noticed flakes in the ice for over a year but thought it was the water. The wire bar from to stop making ice had to be moved from the old icemaker to the new one as well as a brace on the bottom of the icemaker and the front cover. This is all easy. The hardest part of the repair was getting the larger drawer back on its guide. Honestly, this was a repair my 11 yr old grandson could have done with some supervision. I'm guessing I easily saved $100 by repairing this myself.

Extremly easy - just followed the video exactly. Changing the ice make out couldn't have been more easy. when the ice maker was out - noticed some ice build up in the filling water tube. Used the hair dryer to defrost (will replace the double outlet water valve to stop this once my husband is there to help me pull out the frig.) We now have perfect ice cubes. still slowly having issues with some ice build up - but know the water valve is bad too. more to come!!

replaced ice maker, followed the on line video instructions and it was the easied repair i've ever made it took less then 15 minutes

The replacement ice maker was exactly the same size and model. All the mounting screws lined up and install was snap. The website parts description was very good and helpful. We now have ice cubes with no over flowing glacier in the ice tray.

Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.

The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.

Unlike what the online video showed, my bottom freezer French door refrigerator didn't use hooks to secure the icemaker in place. Instead, it used three tabs with screws to secure it in place. I could see two of them, but not the third one. After removing two screws and realizing that the icemaker was still pretty well secured, I felt around and found the third screw (at the top, right behind the front of the icemaker). Once I got that out, the replacement went easily, as shown on the video. That third screw was a little challenging to put back, but after a few tries I got it in. The icemaker is now making ice like a champ! Good work PartSelect! And the part came quickly, as advertised.

The problem had occurred twice before and the metal auger could no longer be reliably forced back into alignment with its end cap. It was time for a replacement. I opted to replace the entire auger assembly including the crusher blade - a total of three individual parts in this assembly. With the Amana model and serial number in hand, I logged into PartSelect and found the ice maker part(s) in the fridge schematic diagram. I ordered the assembly which arrived early. It is easy to disassemble. Remove the ice drawer from the freezer, minus the ice, and place it upside down on a work surface. You only have to remove four screws; the two on the front bottom of the ice drawer and the two screws holding the little L-shaped brackets that receive those two bottom screws. Tip: To avoid any confusion during reassembly, just take a picture of each step of your disassembly. You can do it Noonan.

Easy to replace part - remove panel at the bottom rear of the appliance, unplug from the compressor and connect the new relay. Unfortunately, it was not the relay on my appliance -- looks like the compressor has gone out -- new fridge for me

First pulled the Ice tray out of the freezer, Pulled the cord for the power to the refrig. Removed 3-Srews with the nut driver and disconnected the Power Supply to the Ice maker. Removed it from the freezer and started to remove the Bail and install the bail in the new Ice maker. Remove the cover from the side of the old ice maker and install it on the new ice maker. Put it back in the Refrig and connected the power cord and installed the 3-screws and reinstalled the Ice Tray and 30 mins. later it started making ice. Thanks for the Youtube Video it helped a lot to take the pressure off of doing it your self.