36058 Refrigerator - Instructions

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

Followed the video as a guideline. It was not exactly as portrayed. My husband and I, being long time do it yourselfer's, were able to get around the differences. There were screws, instead of tabs as pictured in the video, plus had to remove 4 screws instead of one to loosen the old icemaker. After 2 days the icemaker is pumping out loads of ice.

I performed the replacement just as the video instructed. Very simple repair.

Looked at questions, picked one that applied, ordered suggested part, fix was super easy after watching video, Frig in running, part fixed it. Very excited, Thankyou.

One mnorning the temp on the frig was in the 50's and the freezer was cold. Tried to get someone to come out and repair with no luck. We purchased a new frig. Then I decided to see if I could repair the old one to use. I wish I had discovered partselect before I bought the new one. First I thought from the web site that it was a overload/relay problem so I ordered it and changed it out and it was very easy. Then that did not correct the problem so I checked further and discovered that it could be the defrost heat element and thermostat. On partselect web site I saw where if your coil is covered in ice that this could be the reason. I ordered them and watched the video of how to change them out. The video is a little misleading because chances are you will not have the room around the coil that it shows on the video and also the element and thermostat will not come as one unit as shown on the video. It is still easy to cut the wires ont he thermostat and install it. The heat element is a little tricky to get out and back in and the clips that holds yours might be a little different and more difficult to do than the video but you can do it. All in all I spent about 160. 00 And the frig is working like new.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

I followed the instructions from your video. I did this replacement all by myself. I am a 64 year old woman and have never done anything like this before. It could not have been any easier.

Replaced icemaker and used wire harnnes and plastic cover off old one. Real easy!!

The ice maker change out was easy. The problem was the part came with a different filler cup but the one needed was supplied. Changing to the other cup required taking the ice maker apart and installing the other filler cup. Go to the parts list and find the filler cup. Use instructions found there to change to other cup and then install your ice maker.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

First off I had no idea how a fridge worked or where to begin and the troubleshooting section of the manual was a joke. So I took the back panel off made sure the coils underneath were clean. Took out the back panel of the freezer and made sure that nothing was frozen over and I hadn't seen excess water on the floor so ruled that out. I knew the condenser was still running so I took a shot in the dark. Ordered the part and waited for it to arrive. It took me 3 minutes to open the box and install it. Immediately knew it was working replaced the back panel and moved the fridge back.

removed old icemaker and transfer some of the parts to the new icemaker. The only problem was that I had to disasemable the new icemaker to replace the fill tray with the older style (which was included). Once that was done, installation was pretty easy.

I removed the old ice maker as described by the DIY video and had no problem except, I had to remove the ice tray from the motor section so the end cap could be changed. This only required removal of two Phillips screws on the case of the motor assembly, that are used to to secure the tray. Once the tray was off, the ice ejector could be removed and the end cap was free to change. Everything was re-installed in reverse order and unit was mounted. An FYI to anyone with slow ice making, will need to check their freezer temperature. Make sure it's set to get as cold as 5-10 degrees Fahrenheit. After installing new maker, it was not making ice fast enough, only to find my freezer temperature needed to be changed as well. Everything is working as it should now.

My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!

The ice maker was easily replaced, however I still had no ice. I ended up using an on-line repair service which determined that the problem was the water inlet valve. Replacing it was beyond my expertise so I hired an appliance repairman.