31213WAV Magic Chef Range - Instructions

We were at a loss for a long time without my boost burner and then while checking all the rest of the burners my husband discovered that all of them had a massive amount of rust on the underneathe side of the burners and that worried me. Well as usual my husband took care of my worries when he discovered Parts Select. We both were pleasantly surprised when we found out that you had what we needed. And the installation was less than 5 minutes, WOW, THAT WAS GREAT! Thanx a million!

The spark module pulses a stepped up voltage to all four burner sparks at the same time regardless of which burner you want to ignite. I read that this part lasts about 10 years. I don't cook much and it lasted 13 years. On my Magic Chef the part is behind the right side wall panel. Lift the range top,remove all the screws that hold the right side panel in place. This replacement can done without opening any gas fittings.

The oven in my Jenn-Air range started to leak gas whenever I turned it on and a visit from the local gas company indicated the ignitor had probably gone bad. I had assumed the older range wasn't worth repairing but didn't want to spend $800+ for something in otherwise excellent condition. Internet research yielded lots of tutorials on how to make the swap and I decided to see if I could get the old part out before going any further. It wasn't too tricky except one of the two screws holding the ignitor in place had stripped and it was in a location that was very difficult to reach. I used a part of tin snips to cut around it. The new part ordered here came very quickly and exactly matched what I had removed; the wiring harness fit perfectly. It was a snap to put back in and now the oven works perfectly. All for under $50.

My oven would not come on so my wife could bake a cake. The glow coil that ignites the gas for the oven had burned out. The replacement went very easily and fast. This web site was very helpful with all the information I needed to get it up and running again. I enjoyed the cake she made after I got it fixed.

We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.

Removed oven door, bottom, bottom of broiler and back metal shield. Just unscrew old igniter and unplug wires and install in one. No problems.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

1/4 turn counter clockwise to remove the old burner, removed wires. Placed wires on new burner tightened them with pliers,dropped it in, 1/4 turn clockwise--done!

remove oven door (watch video) remove bottom drawer clipped off plastic connector and wirenut to existing wiring. use nut driver to remove old igniter and install new one they even supply wirenuts and new insulation. Instrution are very detailed and easy to follow.

Watched the u-tube video of the repair linked to the PartSelect website and followed the instructor. The screw on the old igniter was a bit rusty and stuck on tight but it came off with a bit of coaxing. I can't the part arrived so quickly and that the repair was so simple. I am so happy we did not have to buy a new stove!

Watched the you tube video. A tremendous help. Now it works great. I will definitely buy parts from you again!

I read some of the other comments and my problem seemed the same so I order the flat style igniter kit as suggested watched the video that Parts Select had, just to see any hidden tricks or tips .The installation was done in about 10 minutes it took longer to put the door and grates back in place simple. Phillips screwdriver was all I needed, I had a flashlight to see better cause my eyes aren't what they used to be

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Removed oven door, pulled oven out to acess the rear of unit. Removed two screws inside the oven that connect the ignitor to the mounting bracket. Used flashlight to find plug that is connected to the ignitor located at the rear of the oven. I could see the plug in space provided in the oven rear cover plate. Did not have to remove anything to access the plug. Unplugged connector, tied string on connector and removed ignitor from inside the oven. Tied string line on new ignitor plug and pulled the new ignitor plug to the back of the oven by pulling on the string line. Connected plug and installed screws in the mounting bracket and turned on oven. It worked fine. The hardest thing to do was pull the oven from the wall and put it back. The wife had a good opportunity to clean the crap from the floor under the oven so it was good to move it out. Easy job and so far everything is ok. I am very satified with the part

uninstalled old igniter like video showed and reinstalled new one and then tested right away thank you for your help