Models > 31213WAV > Instructions

31213WAV Magic Chef Range - Instructions

All installation instructions for 31213WAV parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 31213WAV
211-225 of 283
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My oven would not heat.

  • Customer: MARY ANNE from WYOMING OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I ordered the igniter part and receive it the next day with standard shipping. It was very easy to intall it took about 15-20 minutes and your repairman video was excellent.

Replacement of Burner Orifice Fitting Assy.

  • Customer: Godfrey from Las Cruces NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Started off as attempt to make some top burner igniters work; failed to notice that pulling up on front of range top to gain access to igniters is wrong approach and stresses aluminum gas supply tubing; broke left and right front burner tubing, but managed to change igniters after noticing and removing small screws that hold orifice fitting assy. in place under stove top. Expensive lesson. Igniter ceramic insulation was broken but piece remained inside each of two and was Super-glued into place; fix worked on both but later failed on one, which had to be replaced with new igniter. Oil filter wrench worked well for unscrewing burners.

The Oven was taking too long to light

  • Customer: SHARON from SADDLE BROOK NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was very easy we followed the video and it was very easy.Thank you PartsSelect!

Oven was not igniting, but broiler was

  • Customer: Timothy from Lamoille IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband and I were prepared to go and buy a new oven... WE ARE NOT DIYers, but I looked up the model no and problem on the internet. Thank heavens I found the PartSelect site. The best part was the YouTube video!!! It was the easiest repair. For under $50 and 30 minutes our oven works like new! My friends were so impressed, they have asked for the website!!!

burner rusted flames coming out the side of the burner

  • Customer: Lewis from Tomahawk KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
turned the old burner to the left and lifted it out. unpluged the wires with a screwdriver pluged the wires into the new burner and putit back on the stove and turned it to the right

repair range burner

  • Customer: ZHENG from PINOLE CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
in and out in 15 min ,is easy when part fit.

Bottm of burner rusted out

  • Customer: Paul from Oxford MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
took my right hand twisted burner off unplug wires pluged them back into new burner and put burner back on done 3 mins tops.

The ignitor in the oven wasn't working

  • Customer: Brenda from Ottawa IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
I was a little intimadated as I hadn't tried any type of repair like this before. My oven is almost 20 years old so the ignitor was hard wired; there wasn't any plug. I wasn't able to remove the burner assembly so I had to do all my work inside the oven. I had to cut off the plug and hard wire it to the oven. It works great now. All I noticed was that the oven temperature is higher than what I set it at.

bottom oven not getting hot

  • Customer: Nicholas from Detroit MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took the old igniter out by taken some screws from the top had to remove the bottom cover underneath then had to cut one of the wire on the igniter put the new one end put the screws back in plug in the oven back iand then check to see that the oven will get hot it did the repair went well.

Original igniter took 20 minutes to light oven

  • Customer: Bernadette from Lima NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the racks and bottom tray in the oven. Unplugged the old igniter and plugged the new one in.

ignitor failure

  • Customer: Barry from Baton Rouge LA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Great.... thanks!

Oven would not heat

  • Customer: Mike from Wrightwood CA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I found that the igniter would glow but the burner would not light. I was not sure what part I needed so I went searching the internet and fortunately found "Part Select". Your trouble shooting guide not only told me what part I should buy but demonstrated how to do the repair with a very helpful video. Thank you PartSelect for the the excellent customer service! Mike Dicken Wrightwood CA

Oven would not light

  • Customer: Kenny from Pinon Hills CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy repair. Removed door, shelves and bottom cover over igniter. Removed two screws holding igniter, unplugged wire and removed igniter. re-installed all parts.

No oven, no broiler, top burners worked fine.

  • Customer: Bruce from Silvis IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Since I had never done anything like this, I watched your video twice. The oven door and racks came out easily. The wire connectors had burned, fusing the plastic parts. I cut them off and spent more time looking for a wire stripper than on the repair. The new igniter looked just like my 1993 oven part. Works great. Be SURE to unplug and turn off gas before starting!

Oven wasn't baking but broiler was working

  • Customer: Cheri from Fishkill NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the part from this site. It arrived In the time thy said it would. Removed old oven igniter and replaced with new one. Removal of screws and old igniter. Replaced with new igniter and put screws back nd it was working again
All Instructions for the 31213WAV
211-225 of 283