Models > 31213WAV > Instructions

31213WAV Magic Chef Range - Instructions

All installation instructions for 31213WAV parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 31213WAV
256-267 of 267
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Theromostat Knob loose and missing degrees

  • Customer: Avon from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Repair was is push knob in over the stem. and it was secured and in place.

light bulb socket broken

  • Customer: Blanche from Woonsocket RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.

Oven Would not Light

  • Customer: Neville from Lithonia GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

Oven would not ligth, igniter did get red.

  • Customer: Fred from Juneau AK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the igniter, several people on this site agreed that this is the problem and they where rigth.I t was an easy fix. I live 60 miles from the next town and repair shop. I am out in the Alaska bush and can only get to my place by boat or by floatplane. Thank you all you self fixers for your help.

The oven would light, but the flame was very small and it took 30 minutes to preheat.

  • Customer: Bradley from Louisville KY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video, it's too easy and best of all, the part fixed the oven!

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Oven Failed to light

  • Customer: Mark from Middletown NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Once I noticed the oven failed to light, I checked the igniter and saw it was glowing. At that point I did some research and found that the igniter could still be bad even though it glowed. This was the most common cause of ovens not lighting. A bad igniter will not glow as bright as a new one. An igniter had to draw a minimum of 2.8 amps in order for the safety valve to open and supply gas to the burner. After checking the safety valve with an ohmmeter, I found it to be good, so I ordered a new igniter. Once I received the new part , it took about 20 minutes to install.

The igniter on my stove wouldn't ignite.

  • Customer: keith from massillon OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched a video on replacing igniter. Removed old igniter and replaced it with new igniter.

Burner flame was poor and yellow flames left sute marks on pots and pans

  • Customer: Jeff from Oconto Falls WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
twist old burner and lift out disconnect two wires throw away gasket (if there is one left) connect two wires to new burner set in and twist till tight total time 45 seconds

Door seal was pulled out by grandson.

  • Customer: Michael P from Hickory Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.

Two mounting screws were bonded from heat and stripped the threads.

  • Customer: Donald from Dixon IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Replaced stripped screws with 632 by 3/8 bolts and nuts. Your video helped with the rest of the installation.

range- top four burners will not light

  • Customer: Rick from Brockway PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed rear cover where the spark module was and change it
All Instructions for the 31213WAV
256-267 of 267