30-4988-23-05 Tappan Range - Instructions

I first removed the 2 screws that held the oven floor in place. Once removed, I remove the cover plate that covered the ignitor.

In order to get to the ignitor wires, I had to remove the drawer. Once the drawer was removed, I marked which wire went to which spot on the ignitor, then cut the wires. I then removed the old ignitor by removing 2 screws. I then attached the new ignitor with the 2 screws and attached the wires using the enclose wire nuts.

The complete process was very easy, taking less than half an hour. The part with shipping was just over $50. If I paid someone to fix my problem it would have cost at least $200. I'm sure galad I found this web site.

the repair was simple and it was so easy to order thanks to your website my stove is as good as new.

We have an older .......range that came with our house when we bought it in 2000...the stove works fine (for an electric stove!), but the drawer was always problematic. Sometimes it would sit straight in the appliance cabinet and sometimes it wouldn’t. Sometimes it would flop up and down, sometimes it worked and sometimes it didn’t!

We lived with it for TEN years...then a couple of weeks ago I needed a pizza pan. I opened the drawer and the darned thing wouldn’t go back into the stove properly. I played with it for awhile, trying to figure out why it didn’t work correctly! After some energetic observation (accompanied by some choice words about American engineering!) I realized the front drawer guide was broken off!! It was one of those “Aha!” moments!!

I retrieved the plastic piece and went to a local appliance store to get a replacement. They said they’d order one (for 8.95 and I pay shipping and handling!), and it would take 2 to 3 weeks to get it! I declined their offer. Surely, somwhere on the internet there was a supplier who had this part!!

I sat down with my MacBook Pro and looked up “range parts” and was immediately directed to partselect.com. I looked up the part (which was ONLY $3.38) and ordered two. I had the parts in my hand in four days, and even with shipping paid less than half what the other place wanted locally.

I pulled the drawer out, literally dropped in the new guide, and the drawer has worked flawlessly since!! We are forever grateful for PartSelect and will always keep their address on top of our web vendors list!!

Give them a chance...the least you could do is save some aggravation, and maybe a little bit of money, too!!

wonderful went perfect!!!

Unplugged the oven
Removed racks and bottom plate
Removed two 1/4" fasteners on ignitor
Installed new ignitor with two 1/4" fasteners
Cut each wire on old ignitor one at a time and hook up using included wire nuts
Plug in oven
Test oven
If it works, put it back together

followed the instructions that come with the part. very quick and easy.

could not determine what part failed.Found Part Select on line useing Bing search.Using virtual repairman and typing in the problem it told me what I needed.Orderd that part on line and reieved it in TWO DAYS,can you believe that! Inatalled that igniter in 15 mins. and now it works like new. Thank You Part Select!!!!!!

I watched the video before ordering the part. When it arrived, I knew exactly what to do. No tools were needed. It took me 2 tries to get the drawer aligned properly but the whole repair took about a minute. The video was invaluable!

Wow! That was simple! I did not even have to run all over town looking for the parts. I just hopped on the web, checked out the online diagrams, ordered and the parts showed up in the mail within a few days. It could not have been easier. Parts Select is now in my bookmarks for future use.!

Thanks guys

Removed old glides and replaced new ones.

Replacing the faulty ignitor would have been simple enough if my arms were a foot longer and the bolts that secured the old ignitor had not been baked on.

With an ample dose of WD40 and some Vise Grips I finally got them broke loose. An Ohm meter can tell you pretty quickly if the old ignitor is bad. My old ignitor measured more than 1 mega ohm while the new ignitor read only about 346 ohms.

followed posted repair procedure on Parts select site. . . straight forward and simple. . .

I removed the oven bottom which was held by two large head long screws. I then removed the heat deflector using a small socket. The only difficult part was when I went to replace the igniter. The screws that were holding it in place stripped I guess do to the amount of heat they were continually subject too. I had to apply pressure to the igniter bracket while removing the screw using a small socket. Even with that they did not come out easily. If I had not had trouble removing the screws the repair probably would have taken 15 min.

The philip head screws holding the igniters were frozen. Had to cut off heads with dremel cut off tool, then grabed residual screw with vice gripp pliers. Removed screws and mounted new ignighters. Used new hex head bolts. Attached wires per instruction sheet and tested unit. It worked.

Removed drawer and replaced broken and missing parts. Very easy when you have correct parts.