30-3859-23-02 Tappan Range - Instructions

My husband was able to easily remove the old part, and replace with the new ignitor. The wires were long, so he took the extra precaution of tying them away from the flame. It took longer to take everything out and put it back together than the actual repair..

Remove the oven drip pan & burner baffle. unscrew & cut leads to remove old igniter. Splice old leads to new using furnished wire nuts and remount. Job would have been easier with oven door removed, but didnt want to create a new project.

took off bottom pan in oven and replaced ignitor

disconnected the (2) wires of old igniter from (2) wire nuts located under oven in back of bottom drawer, took out (2) mounting screws holding igniter assembly and held it together to new igniter assembly. Stretched out wires together and cut new wires same length as old wires, then mounted new igniter with same (2) screws and connected wires with new included wire nuts and replaced all other oven parts, turned on oven and had a nice TV dinner! :-) Extremely pleased with PartSelect. Ordered part on Tuesday night and had it by Thursday night the week of Christmas no less! Kudos to PartSelect! Great service!

Removed broiling drawer to gain access to the igniter. Remove igniter from mounting bracket, ,cut wires, attach new igniter wiring and reinstall the igniter on the bracket. Reinstall the broiling drawer to complete the job.

The day after Christmas I searched the net reading various reviews, etc. PartSelect seemed to be the easiest site to navigate and offered How To's notes. Wednesday, less than two days later the oven igniter arrived. This was the third igniter in six years. The grandkids watched me intensly as I read the How to's and easily installed the new igniter. Because of the ease with the website and the fast delivery I am keeping PartSelect.com as part of my resources for the home self doer. The cost was competitive saving me over $100.00 doing it myself. Thank you PartSelect. Joe W Cleveland, Ohio.

Removed racks. removed two screws in back of bottom shelf of oven.Do not know what type of nut or other fastener was on other end of those screws as they would not tighten when I put them back in. However they are in the holes and the shelf isnt going anywhere.The shelf lifted right out lifting the back up first and sliding out from under lip in front. easy access to igniter use a nut driver for this.In the bottom left corner there was a triangle shape cover that needed removed held by one screw. both wires had clip in style connectors that come right out.Cut these off with plenty of wire to attach to new wires with wire nuts provided with new igniter.Put everything back like the old came off. I used a little electrical tape over wire nuts.Closed oven door and tuned on oven and watched my wife begin to smile as the igniter turned red and oven kicked on.

took off door, oven floor and burner cover. cut the wire for the old igniter and used ceramic nuts (provided) to hook up the new one. screwed the new one on with old screws, tested and re-assembled. Saved a hundred bucks easily, but I have some basic electrical back ground.

Easy peasy! Took all of 2 minutes to replace all four clips. Clips snap in by hand and take a little bit of force to make them seat correctly. These are a frequently-replaced item,so that makes me think they are somewhat fragile. Great prices and quick shipping from PartSelect made this so simple. The local appliance parts dealer wanted $11.00 each for the rear clips! Thanks!

First, I took out the racks. Then I removed the bottom cover of the stove. (This was in place by two screws that I used my drill & socket set.) Next, remove burner cover by a socket set. Finally, in the corner was a metal cover that covered part of the electrical connections. I then used the screw driver to undo the screws that attached the igniter to the oven. I undid one wire connection, and wired it with the new one on the igniter. (To make sure I wired it correctly.) Then I undid the other wire, and connected it with the new wire (using the new wiring nuts provided.) Done! Now just put all the parts back together.

We just recently purchased our home. The gas stove top is stainless steel and works great but the drip pans and burner grates were old, worn, and not very attractive looking. So I decided to replace them with new ones to give my stove top a fresh at like new look.
Thank you so much. They worked great.

The plastic drawer slide that the lower stove door sits on broke. (one on each side) Remove the old one with a screwdriver and snap in the new one, took 1 minute because I replaced both of them.
Excellent fast delivery. 5 stars !

remove/pry broken plastic glide from in-side of oven,( wall not drawer ) and install new one.

No tools were required. All I had to do was lift off the burner grate. I removed the old drip pans. Put the new drip pans in. I then put the burner grates back on. I did this with all four burners. That's all there was to it. Easy as 1-2-3.

After reading the input of others on your site I ordered the igniter. Within a short time it was installed and the oven works fine. Thanks for the help, jc