2599W Amana Refrigerator - Instructions

Removed ice container, replaced end cap that holds Auger shaft that connects to shaft that turns the Auger. End cap plastic nubs wear where it makes contact to the turning stub. Removing a few screws on the front of ice container allows the Auger shaft to slide forward and away from the end cap. Maneuver end cap from shaft, replace using same maneuver and that is it.
Pretty easy, even for a novice like me. A $6.00 end cap verses the whole assembly at around $70.00
I'm pleased.......

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

I removed the panel to gain access to the condenser and found it to be a solid block of ice. I ordered the 2 parts, I suspected and they arrived in 3 days. I replaced the parts and let it run for 48 hours. All is well and the frige gets colder than before.

First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.

I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.

Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.

I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed pin holding the wheel along with leveling screw. Put new wheel in place, replace pin and screw. Done...very easy.

I replaced the defrost timer, and then the defrost thermostat. I diagnosed these two items because it would get cold/freeze great for about 12-24 hours and then would start to warm back up. I pulled the cover off that covers the evaporator coil and found it to be frosted up. This told me that the defrost timer probably wasn't working properly. Decided to replace the defrost thermostat while I was in there as a precaution. It was much much cheaper than having to replace a side by side!!

pulled cover off back of refrigerater at the water line,shut water off removed water line,check for pressure at the line by puting the line into a 5 gallon bucket it was ok.took the dispencer lines off that goes up to dispencer,hit dispencer switch could hear buzzing at the dispencer unit but no pressure.so i replace water inlet valve

The defrost circut stopped working which caused the coils to frost over stopping the blower and freezing the water line. Take everything out of the freezer, remove lower back pannel held in by around 8 screws inside the freezer. The thermostat was attached to the upper right coil. It clips on to the coil. Wires attach to the fan and defrost heater. A pair of wires runs out through a hole. These wires are to measure thermostat. It will read 0 ohms when frozen. Rremove and replace the thermostat. The defrost heater should read around 25 ohms. Remove the bottom grill. It pops off. The box in the middle houses the defrost timer. Remove the 2 screws holding the box to the chasis and then remove the defrost timer screws... Before buttoning everythigng up, plug the fridge in to the power and wait for about an hour. The fan in the freezer just above the coils should be running and circulating cool air through the fridge and freezer. Depending on how long your freezer was unplugged, the water should be thawed enough to dispense water again.

For the icemaker, I removed the ice tray and loosesned the two attaching screws(1/4"). I removed the lower bracket and then removed the ice dispenser motor cover below the ice maker. This made it easier to remove the wiring harness. After removing the icemaker from the refrigerator, I swapped out the wiring harness and ice detector bracket (wire bail that swings). Hooked things back up and went on to the water valve. All in all about 15 minutes and pretty easy.
For the ice valve, you must turn off the water supply, disconnect the power plug and move the refrigerator away from the wall. (Now's a good time to clean out under and behind the unit!) Remove the valve from the base with the 1/4" nut driver. Remove the inlet line(standard hose fitting).Have a sponge handy. Remove and replace the new valve in the bracket by popping the clip off and on the new one. Replace one outlet line and electrical connection at a time (easier to keep track of). Replace unit on base and check for leaks before replacing refrigerator. Other than cleaning, the task took about 20 min. and was simple. The cleaning, on the other hand...

First I turned the water off behind the refrigerator....took the ice maker inlet valve off, put on the new one. As simple as that & it is working beautifully....not only am I a woman but 55 yrs. young too!
With the right part & right tools NOTHING is impossible & I saved myself a repair persons fee!!!

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

Tried to repair existing valve which I have succesfully done many times by cleaning and removing grit from internal neoprene parts until new parts received. Was not successful. New valve worked perfectly. this is only 2nd repair needed on this ref. since new. 1st was defrost timer. Ice maker hasn't missed a lick since new.

The door seals arrived in good condition, I followed the instruction and unpacked the door seals and straighten them out on the floor. I left them over night to climates. First I empty all the door compartments of food. I then used socket driver and loosened all the hex nut screws around the door. Do not remove the screws. Removed the door seal by pulling it out of the door seal clamp. Once removed clean the door seal clamp and door. Now start at the top and put the door seal into the top door seal clamp. Then work on both sides of the door pushing the seal into the clamp. Finally stretch the seal and insert the bottom section into the door seal clamp. Check and make sure the seal is properly installed around the door seal clamp and the fit is even. Start at the bottom and tighten the bottom screws. Then start tightening the sides and finally the top screws. Make sure there are no wrinkles. If there is undo the screws and reposition the door seal. This is an easy install but takes about 2 hours to do.

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self