Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Fridge would not cool at all, because the compressor was not running. Fan running, lights working, just no cool.
Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.
Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.
Turned off fridge circuit breaker Removed all food from freezer and put in cooler. Removed shelves from freezer Removed ice maker Removed 2 hex head screws Tilted back evaporator cover and tried to unplug connection. Found connection was iced over with a huge block of ice coming from water inlet to ice maker Spent several hours trying to melt and chip away ice without damaging fridge. Finally was able to break up ice with long flat head screwdriver and hammer. Unplugged connector and was able to remove evaporator cover. Cut wires near thermostat and removed Stripped wire as needed and crimped new thermostat in place. Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected. Reconnected evaporator cover connection and reattached cover. Reinstalled ice maker Reinstalled shelves. Put food back in Turned circuit breaker back on.
Fan was off kilter and began rubbing the frame which is caused it to slow down and make an disturbing audible noise.
Before buying the part, I watched your video and realized it was extremely simple to remove and replace. Item was to take 7-10 days and I received it in 4. Took longer than 15 minutes because I had to move the fridge forward, get my tools and a vacuum, get a cup of coffee and get to it. Very easy and the video was exactly step by step. It took longer to vacuum all of the dust bunnies than to replace the part.
Honestly, I was in the market to buy a new refrigerator but now I believe I'll wait several more years. Thank you for your support.
Fridge was cooling down enough the heating defrost was bad
I take 2 crew on front of the fridge take the cover and fan out replaced the part and put everything back it’s a easy job thanks guys for the parts from Orlando fl
Disconnect the power. To install the Defrost timer which is located inside the console at the top of the fridge I followed a YouTube video. It is very easy. Keep in mind that the Defrost timer comes settled in defrost mode so the compressor will not start after the power is reconnected.There is a hole in the console just behind the Defrost timer where you engaged it with a flat driver and rotate the clock until the compresor start. Now the compressor works for 6 hours and stop for 20 minutes for the defrosting cicle. The freezer now is freezing the meat!!
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker. 2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,. 3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket. 4.Now take out 8 screws that hold the back panel in place and remove the back panel. 5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.
You have sent the wrong part for the THIRD time. You have sent aaccess cover that is TWO INCHES too short. It does not cover the opening, and you will not answer your phones.
There is no way to complete the repair with the wrong part, You have had my order since June 22nd, 2020 and the incorrect part arrived October 27th, 2020. You charged $7.79 plus $1.06 tax and $9.95 shipping. Please refund the entire amount including the shipping, since I did not ask you to ship the incorrect amount.
Just slid it in. Fit perfectly. Called the Help Line just to double check that the pan would fit and they assured me it would. Pan cost $20 less than through the Sears site because of lower price, lower shipping and no taxes. Oh, and the pan came in just two days. Very happy.
refer door hinges were lost during the move in to our first home.
The center door hinge was still attached to the refridgerator so I only had to install the bottom and top hinges. I also moved the door handles to the other side so the doors open the "right" way. The hinges were just 2 bolts and 3 screws. Now, just if the repair man from our home warrentee company would show up to fix the refridgerator. It's blowing hot air!!!
A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.
