Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
It Was Fast And Easy, No To Mention Affordable.
Removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the wires. Everything matched up perfectly.
The ice maker would over floew then not cycle it would freeze with the forks stuck in the ice! so just get your modle # and serl, # call in and order the hole ice maker it cost only about $120.00 with shipping!! it is so simple to put in just lossen the 2 1/4 screws in the back and lift up then unplug it. you do not have to turn the water off as it works off the pump at the bottem !!( note you nedd to take the ice bucket out it just slides right out !! You will save the service call from A repair man it is really very easy so by the time it took to read this you will have it done !really its that easy!!
After earlier determing that the starter switch was at fault, I removed the cardboard lower back panel, shut off water to the ice maker, removed water line. The plug to the compressor containing the switch and capacitor was held on by a spring clip, removed clip pulled wires from old switch (Here needle nose pliars are handy as the spade clips on the 2 wires have their own locking clips) replaced switch and all wiring, tested unit and problem solved.
I removed the old gate by using a flat head screw driver to pry open mouth. I then removed 2 bolts that held on the cage that hols the ice crushing blades. Then I inserted the new gate and used a screw driver to pry the mouth open again (it was more difficult to insert than remove). I then popped in the new gate and re-assembled the cage. It worked on the first shot with no problems!
This is the 3rd time I have attemped and successfully repaired major home appliances myself after the warrenty ran out. I'm sure I could buy a new appliance for the money I saved.
I shut the water off under the sink and removed the back piece on the refrigerator, unscrewed the water valve, cut the ends off each plastic hose and reinserted into the new water valve. Then rescrewed the water line into the new water valve and turned on the water. Unfortunately, I was not able to get water out of the door and the ice maker still doesn't make ice. While this was an easy procedure, it didn't help me. I'm not sure I needed to replace the water valve.
I had had a repairman look at the problem, and he estimated the cost of the repair to be $225 to $500. Needless to say I was quite happy that I was able to do it myself for $85.
I found that getting the water/ice dispenser back in place was the hardest part because the water hose is so short. I finally threaded a stiff wire up into the hose and guided it through the dispenser opening. The rest was pretty much routine.
A plastic guide rail broke after the meat keeper drawer was left open and the refrigerator door was shut on the drawer, this has happened a few times over the last 6 years. We chose to change out both rails at the same time. We removed the meatkeeper drawer, then the shelf above as the rails are attached to the shelf. We removed the rails (one screw on each side. When the new rails came in, we replaced them with the screws. Super easy!
Pulled the drip tray out of the ice/water dispenser. Removed 3 screws, pulled up the beauty ring. Removed 3 more screws, pulled out the circuit board, and plastic plate that it is installed in. Removed screws that hold the actuator in place. Unplugged and removed broken actuator, installed new actuator, installed hold down screws. Plugged in actuator. Installed beauty and other parts in reverse of removal. Would probably recommend removing door handle on the dispenser side. Would make installing one of the screws much easier. But you have to remove 2 small hex screws to remove handle.
loud crack when fridge door opened past 90 degrees
Unscrewed screw holding plastic clip on right hand top hinge. Unfasten two lags screws holding right hand top hinge. Lift door off bottom hinge. (Do not unfastened bottom hinge) Remove old plastic bearing and replace with new. Repeat aforementioned instructions in reverse order. DOG EASY.
Water was leaking from the filter area when in-door water dispenser used
Silly me. It couldn't possibly be the filter because it's worked for the last 9 months with no problems. Decided to replace the water filter base first. Repair was easy. I saw someone had trouble removing tubes from old base and I gave it a couple of tries to no avail so decided to cut the lines instead. Made it even easier. After repair, water continued to leak. So, replaced the filter itself and voila - leak fixed. Make sure you check the filter first. My mistake turned a $40 - 10 second repair into a $100 - 20 minute repair. Good Luck!
Too of the rail supports inside the fridge were broken
First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again. You can do it!!!
Followed instructions from others on the blog. Shut off water and electricity to the refrigerator. Removed the cardboard plate. Removed the old water valve. Cut the compression valves off and inserted the tubes into the new water valve. Attached the water valve bracket to the fridge. Tightened copper water supply.Turned on the water - no leaks. Plugged the fridge in. Tried the water and ice in the door. No leaks - everything worked perfectly. THANK YOU PARTS SELECT!
First I loosened the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...re-installed the new icemaker first attaching the wires and then fitting over the screw holders and tightened the screws. That was it!