Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Fan motor died.
Remove shelves. Unplug unit. Unscrew back panel. Remove wire harness. Remove old fan. Insert new fan. Screw it in. Reattach wires harness. Plug unit in and make sure fan is on. Reattach back panel. Put shelves back in.
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker. 2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,. 3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket. 4.Now take out 8 screws that hold the back panel in place and remove the back panel. 5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Unplug freezer. Open freezer and Remove the bottom 2 shelves and drawers. Remove 6 screws (Phillips) securing the inside access panel located in the back of the unit. Locate the defroster bar which is secured to the bottom of the condenser radiator. Trace the cable to the thermostat that is clipped into the condenser coil. Unplug thermostat power cable located at the top left of the condenser coil, and the defroster bar cable on the upper right. Release metal band that secures bar to the coil at the bottom where the coil and bar are secured. Reverse for installation.
the refrig was in storage for about a year, the freezer door warped
removed freezer door and installed the new one. This was a pretty easy thing to do, although putting the old handle on the new door was a challenge. No knowing that there is a plastic piece holding the top of the handle i broke the that piece and had to order another one. Mean while the freezer was making alot of frost inside, so that had to be cleaned after the new part came.
Loosened the screws all around the door. easier if you take the door off the unit and lay it on a table. Cover the table with a blanket to protect the door finish. Old gasket just pulls loose. Press the raised bead on the new gasket under the plastic strip. Corners were the most difficult. Retighten the the screws and rehang the door. It took some practice to get the bead under the plastic strip.
This did not fix the problem. Call a repairman and he cannot come until 9/11. Food is staying frozen. Alarm sounds for awhile and then shuts off for a bit.
Removed the inside evaporator coil to do inside solder job, use torch to heat solder joints on the outside drier in order to remove it and install new drier. Soldered Heat exchanger line to drier and 1/4” copper line to compressor. Wrapped with new insulation wrap. Pulled a vacuum on system and then charged with 4.4 ounces of 134a freon. Works like a champ again!
This refrigerator was for flowers and came with only one shelf
We ordered extra shelves with the model number of the refrigerator and they did not fit. Upon calling Frigidaire, we learned that the correct racks were sent but they are not the correct size!
It's easy to know how to use a key. I didn't have a difficult part, I didn't have the model # because I had lost my key and the model # is inside. I was able to find the energy saving paper that came with it but it had four model #'s. I called a couple places and no could me. I pulled up Part Select on line and just thought I would give them a try. I got a very nice person (Jeremy) He went thru every model that I had and three out of the four matched so he sent me a key and if it didn't work I could get my money back. I give him a A+ four taking that extra step, unlike the other places. Very satisfied!