Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The oven would take forever to heat up, and sometimes not at all. Othertimes it would heat up, but not stay hot for the entire baking time.
First, I unplugged the oven from the wall. I opened the bottom drawer of the oven to see where the igniter was mounted, which was directly under the bottom pan of the oven itself. I opened the main oven door and unscrewed the 2 screws that were holding the pan to the bottom of the oven. Then, I slid the pan back towards the the back of the oven and it popped right out.
There were 2 hex screws that were holding the old igniter on, so I unscrewed them with my socket set. I made sure to pay attention to which wire was the top one and which one was the bottom one coming out the back of the igniter. I pulled off the wire nuts connecting the igniter wires to the wires of the oven. I striped the wires on the new igniter and re-attached them to the proper wires of the oven, using the included replacement ceramic wire nuts. I re-screwed the hex nuts in, mounting the new igniter to its proper place. I put the pan back and screwed the 2 screws back in to hold it in place.
Plugged it back in, turned it on, fired up within 20 seconds. Good as new.
burners rusted out on one side since the stove is 19 years old
Bought two to try out to see if they fit and worked-popped out the old ones and the new ones fit and worked like a new stove. Came back to this web site and bought the other two so all burners are now brand new without having to replace the stove.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) Then I put the new valve in, put the cover back on the refridgerator and was done. total time 15 minutes. My wife says I'm the man.
Removed oven door. (Open to first position then lift the door straight up). Located igniter in bottom of oven, followed connecting wires to connection block below oven behind the oven drawer. Disconnected the existing wires. Lifted the burner out of oven to disconnect defective igniter. Screws were fused to the burner. Used vice grips to remove screws requiring the screw holes to be retapped. Bought new screws to replace trashed screws. Installed new igniter to the burner rail then set burner rail back in place. Fished the leads from new igniter back down to connector block. Reinstalled leads. Reinstalled oven door. Tested functionality of oven. Everything worked. Reinstalled metal plates back in oven. Reinstalled cover over connection block behind bottom drawer. Reinstalled drawer. With the exception of fighting with two screws fused to the burner rail it is a very straightforward repair and shouldn’t take much more than 1/2 hour.
First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!
Service and shipping were fantastic! I would definitely use Partselect again!
The old ice maker was leaking water when it filled freezing the ice in the accumulation tray into one big lump.
First, I read the instructions that came with the replacement ice maker, which I found confusing because they were apparently written to be installed in some other make of refrigerator. However, after removing the white plastic cover on the new unit and insuring that it was identical to the one that came with the refrigerator, I removed the old unit by first, removing the bottom screw that held the unit to the side of the refrigerator. Then, I loosened the two top mounting screws. slid the unit up and pulled out and away from the side of the refrigerator. Then, holding the unit in my left hand, I pinched the two plastic tongs on either side of the wiring harness where it attached to the outlet at the back of the refrigerator, took the ice maker out of the freezer compartment and set it aside. Then I located the water regulator screw on the right side of the new ice maker and turned it one complete turn clockwise to reduce the amount of water that would fill the unit. After reinstalling the white plastic cover on the new ice maker, I saw that the wiring harness that came with it would not fit my refrigerator's outlet. So I removed the wiring harness from the old ice maker and installed it on the new one. Then I connected it to the outlet at the back of the refrigerator, slid the ice maker over the two top mounting screws and then pulled down to seat the screws. Next, I used a small torpedo level to level the ice maker both vertically and horizontally. This required placing several flat washers behind the metal mounting bracket at the bottom of the ice maker and the refrigerator wall. Once I had leveled the new ice maker, I tightened all three screws and shut replaced the ice receiver tray. Works fine.
Removed everything from inside freezer compartment (food and shelves) Removed inside backpanel that covered the coils. At the top of the coils is where the thermostat was attached. Removed old one and installed new. Has been working since.
I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson
First pull out frig and unplug. Shut off water valve. I just had to remove two screws to disconnect unit from bottom rear corner of frig. Pull element out just a few inches and disconnect the plug that feeds it electric. Disconnect water hose and reattach to new unit. Reconnect electric plug and reinstall in back of frig, securing with two screws. I have an older appliance, so I had to jury rig a bit when reattaching new unit by drilling two new holes for mounting. Also, I had to buy a new water hose because the old part would not accept the standard female end of the hose to connect to. Home Depot has the standard icemaker hoses with two female ends. These two glitches would probably not apply to a newer appliance, but anyway, it's cranking out the ice just fine now! Sure I saved alot of money, even with the extra $10 investment for the hose.
I removed the drawer, and removed the shelf and both rails. In the back were 2 clips to secure the shelf to the frame and stabilize the rails. Then I could move the glass shelf and access the broken rail and replace it with the beautiful new one. I feel like I Have a new fridge! I found the part on line even though I could not find the plate with the model number or year!
Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.
Ice make was still working but no water coming in to make ice . Pulled refrigerator back and found water valve at bottom of refrig close to the floor. I disconnected water line and electric plug - went to whirlpool web site - no help at all to confusing - found partselect and compaired picture of old valve with picture of new valve . When I got it in mail it took 30 min to install - working fine now hint - mark top of electric plug so you install correctly
