Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Kickplate clip broke off
Reattaching the kickplate clip was easy, but the tab that holds in place was broken. It would slide back when the kickplate was installed. I fashioned a replacement tab out of a piece of 3/32 aluminum bent into a U with the hammer. To hold it in place I drilled and tapped one hole and used a 6-32 machine screw.
Turn off water, removed two mounting screws, unplugged solenoid, removed incoming water connection and plastic pipe to ice maker. Installed new valve, connected water lines, reconnected plug, remounted with screws. Turned water back on, over rode power to ice maker and checked for leaks. Total time about 5 minutes. Very easy repair.
unplug the refrigator, remove everything from frezer compartment. remove ice maker three screws and un plug. remove rear panel 4 screws remove motor bracket from rear panel 4 screws unplug motor . replace motor and reasemble in reverse order. the new motor is very quiet.
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
We got a refrigerator at a yard sale for free. The door was off and much of it disassembled. When we put it together we realized the top hinge was missing. We asked the previous owner and they didn't have it. We found it with your wonderful web site which so wonderfully detailed the parts. It was a breeze to put it together and we got a refrigerator for about $30.
The coating in the ice maker was peeling and ice not ejecting properly. The water would over flow over to the ice tray and freez.
Remove the 3 screws and disconect the plug. The wiring harnes on the new Ice Make did not match so I use the wiring harness from my old unit. I pluged the new one in and screwed in the three screws and it was ready. I did have to wait a full 24 hours before the first 8 pieces of ice eject out.
The first issue was to determine if the problem was with the ice maker or the water dispenser / pump. I chose to try to repair the dispenser first since there air bubbles in the plastic line. Also, the ice maker seems to have been working. There just wasn't enough water so the ice cubes were hollow.
I unplugged the power cord, , removed the cardboard backing and two bolts that secured the pump to the refrigerator. I vacumned the area so I could see around. I pulled the valve out and disconnected it from the internal power source. I disconnected the copper water intake and the plastic tubbing to the ice maker. I used a pipe cutter to take the old flanged area off. A new flange was included in the package. I used that and reconnected the copper intake and the plastic tubbing. I replaced the power source and secured the valve to the refrigerator makeing sure the plastic tubbing wasn't twisted. When I plugged the refrigator back up, the ice maker started working within five minutes.
The old water valve leak required me to purchase this new complete part. After shutting off the water supply, disconnect the supply line, take out the old water valve by disconnecting the "plug" from the refrigerator, and disconnect the plastic water line going into the ice maker. Then just reconnect the new water valve by plugging it into the 2 pronged receptacle, note to be sure to write down which wire goes into which input when disconnecting the old valve. Then hand tighten the plastic tube into the valve. Next attach your water supply line into the new water valve, tighten this supply line as you would any plumbing supply line with a couple of adjustable wrenches and some teflon tape at the connection. I would also recommend at this point, if the compression fitting on your supply line was like mine a bit old, to spend a couple bucks on a new fitting and put that on the supply line, since you don't want to worry about it being a good seal at the supply line point, once the repair is done. After checking for "no leaks" reattach everything to the rear of the refrigerator (make a note of the attachment before taking out the old valve) and see if your ice maker starts to make some ice. You will hear the valve feeding the water to the icemaker if all is properly setup.