Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Needed a lint filter
It was simply a replacement filter. No work just replace in slot. Thanks for great service and for sending in one day! We were shocked that the part arrived in one day! Will use your service again!
dryer quit before clothes were dry except on the extra low setting. I got an E1 error reading
flipped THE BREAKER (very important!). Removed the cover on the bottom of the dryer (2 screws), made easier because dryer is stacked on top of washer. Removed the heater box (3 screws). Thermistor located on top of the blower housing (right side). removed old thermistor (2 screws) and unplugged the wires. Plugged the wires into new thermistor, installed the thermistor, replaced the heater box, then tested the dryer. It seemed to work fine. Replaced the cover. It has worked fine ever since.
Dryer shutting down two to five min. into cycle E- 1
Removed the front lower skirt with two 1/4"hex screws. Vaccumed all inner parts exposed. Removed three 1/4" screws holding the blower housing.Memoved the bias thermister again two 1/4" screws. Make sure all inner exaust pipes and rear chimney gas or electric are clean and lint free. Re assemble and test the unit. Install the skirt and make sure the dryer is level Jack, Pa.
Lint filter - The felt piece came apart from the screen unit.
My Daughter and I have the same washer and dryer from Maytag. Her felt piece came apart on the lint filter. I let my fingers do the walking and checked which filter went with the dryer and purchased it. When it got here, I made sure it matched up with the old one and just put it in the dryer where it belonged.
This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin
I read the instructions on the internet. It told me what to trouble shoot first. The switch on the door then the thermo fuse and after that the thermostat. The off on switch on the door checked ok but the thermo fuse didn't when I followed the instructions on the internet. The thermostat did check ok. When I installed the new thermo fuse the dryer started like always before. I was pretty proud of myself for saving a hundred dollars or more. Thank you for the hlpful instructions.Larry
After reviewing the video of the fellow popping out the old door catch with a putty knife and popping in a new one, I tried that myself and there was no way it was going to come out without applying enough pressure to tear up the finish on the door. Tried the option of compressing the catch vertically with pliers and could get top or bottom out but not both. Believe my I have a garage full of tools and am very handy and this method was not going to work on my dryer. Finally removed the door and laid on carpet, took out all the screws and removed the catch from the back by squeezing with pliers. Replaced with the catch from the other side after doing the same.Re-assembled no problem. Ordered a replacement that I put in the unused side for next time.
Pretty easy to fix, hardest part was having to get the screws out of the inside of the dryer to replace the sensor itself. Once that was done it was pretty quick! PLUS super fast shipping on my part!! Was fixed before any repair places even called me back!!
My experience was a positive one. I called the company and read the part number from kitchen aid and the technician on the other line knew exactly what i needed. He gave me the part number and the price and took care of my order. Within 3-5 days i received my part. I am really happy with this company and i will call again when one of my applicances is not working.