11062904100 Kenmore Dryer - Instructions

It was all put together... I just switched them!

remove dryer door....remove two other screws on front panel [left side].tilt panel forward and lift out of brackets.thermostat is visible .remove two scews that secure thermostat. disconnect wires from thermostat and reattach to new one. secure new thermostat reinstall door and front panel.

I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!

this belt is too thin for the capacity of this dryer.I had only removed the front panel,replaced the belt and immediately the dryer start.

Disconnect back of dryer gas/elec then I unscrewed the back panel, and chisel the panel off with a hammer and a old wood chisel to remove the welds spots, changed out the thermostat and I had to use tap screws to put back panel

Removed the old one installed the new one

Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen. Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.

Once I watched a YouTube video showing me how to do the job I ordered the part from you. Am so impressed with your fast shipping and best prices via the Internet. Thank you SO much! The water level switch was easy to install, it ws getting the cover on the washer back on that was hard for me since I am 68 yrs old and have a bad knee. Its why it took me two hours to do what most people could do in 20 minutes.

Unplugged dryer from wall. Removed screws from the back using the socket set. Removed thermostat screws and disconnected wires(one at a time) while replacing new thermostat. Replaced second thermal and tightened screws. Replaced back panel on dryer. Plugged in, turned on and dryer was repaired..

Watched video on locating and testing parts (did help that I had a digital meter w/cont-tone ) removed and cleaned out dryer cabinet tested heating element-was ok went to thermal cutoff (tested bad ) ordered kit from part select parts arrived within two days (fantastic ) replaced parts in thermal cut off kit . Replaced dryer back also and important -removed dryer vent and cleaned out pipe -replaced vent pipe turned on the power tried dryer works like new again your easy to follow instructions made this a very easy job thanks people ! You saved me a great deal of aggravation and more important money

little more than vedio showed has a see thru door had to tke door off machine then was easy replacement and re install

1) Unplug the dryer. 2) Remove lower front panel, use screw driver to push down then pop the top forward. 3) Heating element is on the right. 1/4 inch nut driver removes front plate and the screws holding the foot in place.4) Remove the two wires connected to the heating element and pull the heater toward yourself 5) Remove the screw next to where the two wires connected to the heater, It takes some effort but it will slide out the heating element. Slide the new element in, put in screw next to terminals, slide heater back into place, put foot screws in, put deflector back on with screw, connect the wires back onto the heating element, put the front cover back on, plug in the dryer and test. It will smell for about a minute being new.

I watched the online video first, which made the removal and installation fast and easy.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

I watched the video. Thermostat wasn't the problem tho. It was the timer.