Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 11062202100 > Instructions

11062202100 Kenmore Dryer - Instructions

All installation instructions for 11062202100 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11062202100
76-90 of 1,270
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working but not generating heat.

  • Customer: Laurie from Natick, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hoses. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.

Humming noise then quit after pushing start. Drum would not turn manually.

  • Customer: Derek from Missouri City, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Socket set, Wrench (Adjustable), Wrench set
  • 7 of 7 people found this instruction helpful
Looking at the schematics, it wasn't clear exactly where the motor was located. I took off the rear panel thinking I could get to the motor through the blower. Realizing that was a no-go, I did some web searching and found that the lint screen chute had to be unscrewed, the top had to be lifted to gain access to the top 2 screws holding the front panel to to the main body. The barrel was then dropped and the rib belt removed from around it so I could set it aside. The clips were removed from the front and the back of the motor to gain access to the blower shaft. .The motor shaft is screwed into the blower shaft but it took me a while to figure out how to grab the blower shaft( made of hardened plastic?) with an adjustable wrench while torquing the end of the shaft with a (3/4"?) socket wrench. Access to the rear was rough, but getting the motor out an back in was easy. The spring tensioner for the belt was the next hurdle. With the s-curve facing outward and clipped to the base, the belt with the rib side wrapped around the barrel, the belt was slid between the roller and the tensioner bracket and wrapped around the motor drive rib side inward. I had to take the old motor to kind of prop up the barrel so I could at least see the tensioner and motor interface. I had to do a balance trick where I held the barrel up while centering it to the belt and the rear panel while ensuring the cloth seal was seated to the outside of the chamber. The front panel went on, and the front cloth seal was seated by spinning the barrel. The rest was just a matter of reversing the steps. Tons of lint/dust is probably what crashed this motor. Disassembling the front and the back allowed a thorough clean up - vacuuming and wipe down. Should go another 10 years/

Dryer making squealing noise.

  • Customer: Harriet from Palm Coast, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 8 of 10 people found this instruction helpful
Removed 2 screws in the lint filter and popped off the top. Removed the 2 screws holding the front panel on. Slid the drum off and set aside. Replaced support rollers. Placed the belt over the drum and placed the drum back in the dryer. Wound the belt over the tensioner and motor pulley. Turned the drum to keep seal from folding up. Replaced front and top.

Tip: Use bungee cord or rope to hold top up and out of the way while doing this job.

dryer drum belt broke

  • Customer: Paul from Athens, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
I needed to remove the front lower cover, very easy as it is held on with clips only so I used a flat head screw driver to pop it off. I had to remove the lint filter and then there are two screws attaching the top cover of the dryer to the internal lint filter tray. The top of the dryer can then be opened front to back I again used the flat head screw driver to pop the top open as it has two clips at the front corners. It helps to have someone to hold it open or a rod of some type to keep it open. You can now lay the belt on the top of the drum and work it down the back side by pulling forward on the drum itself to seperate the drum from the seal that presses aginst the back side of the drum. I then went from the lower front to retrieve the belt now draped over the drum and pinched the belt to pass it through the tensioner and over the drive pulley. looking at it from the front the belt will come down the right side of the drum under the tensioner pulley around the drive pulley across the bottom of the drum and up the left side. The belt sits almost in the middle of the drum not against the back lip where there is a groove that might be confused as a place for the belt to ride that is where the seal sits then reverse the process to reattach the top to lint tunnel and reattach front cover and you are good to go . i would suggest vaccuming any old dust/ lint whlie everything is open as this reduces the chance for catching on fire I was supprised as to how much lint was loose inside the dryer cavity itself and our dryer is gas and the flame is an open flame.

Dryer belt broke- drum would not turn

  • Customer: Ronald from Oakdale, CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
This was so much easier than I though it was going to be. Pulled up on the top part of the dryer and folded it over to the back. Removed 2 screws for the front panel and disconnected some wires. Laying down I fed the new belt on and made sure the tensioner was put back into the right spot, because when the belt broke the tensioner sprung to the other end of its travel. Put everything back together. This was made super easy because you guys had the parts and the shipping was super fast. Alot of the local shops in the area didnt even carry the belt or were not helpful..

Dryer was leaving scorch marks on clothing

  • Customer: Howard from Tyler, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 8 people found this instruction helpful
UNPLUG THE DRYER!!!!!
First removed the two screws holding the lint filter in place. Then slipped a screw driver between the top and the dryer body to remove the top. Using a nut driver removed the two screws holding the front of the dryer in place, remove the two wires for the door switch., lift the front cover of the dryer and set it aside. Support the drum ( two extra hands would be nice) and remove the drive belt. Then remove the drum. A thorough cleaning to remove all of the scorch like stain from the drum and back plate. Remove the seal and glue the new one in its place. Put it back like you found it. Make sure that the seal is not tucked against the back plate. Dryer works better than new and no more stains.

Dryer hummed but drum wouldn't turn unless helped.

  • Customer: Leo from Ellicott City, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 7 of 8 people found this instruction helpful
Solution: electric motor replacement as the integral centrifugal switch lever (plastic cam) wears over time causing the start windings' switch poor contact. Took it all apart, (back panel, front and top) including lifting the drum out to completely expose the motor. Needed to wrench the plastic fan from the inside motor shaft. Tricky part was swapping the original pulley (6 rib belt, still good) for the one supplied for 4 rib belts. I needed to file another flat onto the other side of both motor shafts (old and new) to break them free, using a vice to secure the pulleys. The dryer works perfectly! It's a great dryer that can be repaired by a determined novice. The enclosed instructions were helpful, although if followed about cutting the original motor shaft to obtain its pulley might require drilling the shaft from the pulley = nonsense. Thanks again Parts Select.

Start windings burnt out on original motor (dryer would not start)

  • Customer: Frank from Smyrna, TN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 7 of 9 people found this instruction helpful
The repair was fairly straight-forward. I removed the front of the dryer, lifted the top off, and then released the tension off the belt dy depressing the pulley arm. Once the belt was off, the drum came right out and then it was on to unhooking the wiring from the old motor. Very simple up till this point. The snag came when I went to unthread the impeller fan off of the old motor shaft. It was permanently sealed onto the shaft so I had to cut the old shaft into using a reciprocating saw was a metal-cutting blade. Once this was done the new motor installed easily exactly like the old one was mounted. I had to also purchase a new fan due to the fact that I was unable to remove the cut shaft from the old fan. All parts worked great and the dryer assembled back together easily. Works like a new dryer now.

My dryer conked. Would not turn on, but before that happened it was taking way too long to dry the clothes and the dryer would stop in the middle of a cycle.

  • Customer: brenda from Newman Lake, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 7 of 9 people found this instruction helpful
Went on this website and found a story that was similar. I ordered the parts which arrived quickly and I replaced the Thermal Fuse and heating element and it was fixed! The whole repair cost me $24.88! Way cheaper than calling a repair man.
Heater thing was part # 3387134
and the fuse was 3392519

Dryer would spin but no heat

  • Customer: Timothy from Anderson, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
First I unplugged the dryer from 240V and removed the back cover upper (behind the switch) and lower (exposing the remainder of the parts)

Inside the upper section was a folded wiring diagram of the dryer (don't know if this was courtesy of Whirlpool or another individual, but it was a very nice touch.)

I did a resistance measurement across the heating coil and found out it was fine. I then plugged the dryer back in and carefully took voltage measurements from one phase of power (this was easily accessed where the power comes in to the dryer, just be careful not to touch or short the wires)

I had an assistant turn on the dryer (this makes things go a little faster, as you are behind the dryer otherwise) and checked for 240V across the heater coil.

Once I did not have this, I kept one lead on the left side wire (one of the power phases coming into the dryer) and moved the other lead to the left (as viewed on the wiring diagram) until I no longer had 240V. This identified the faulty component as the Thermostat High-Limit, non resetable.

I ordered the kit with the High Limit NR and High limit Thermostat (as both had to be bad). I also ordered the 150 degree cycling thermostat (although this was not necessary - for <$20 I opted to replace it as well)

Removing wires one at a time, each component is fairly easy to replace.

My only complaint is that with the combo kit, the wire attachment is a little different that the original component and requires you to cut an existing wire and crimp a different terminal to allow all three wires on the High Limit thermostat (250 degrees) to be attached. There is little to show you how exactly the crimp is to be connected (it goes on the smaller of the three wires - DO NOT CUT the jumper provided and USE A GOOD CRIMPER - not the $2 variety, or you'll be getting a new connector!!) The connector provided is designed for some strain relief from one connector to the other, however) An additional jumper with the appropriate connectors already attached would be a nicer design.

Also, make sure you do NOT screw in the smaller cover that covers the power in until you place the entire lower half cover back on the dryer (unless you want to take it off a second time, as I did...) as it uses a common screw to hold both in place.

Overall, fairly easy to do with a minimum of tools, straight blade screwdriver to remove stubborn wire connectors (esp. for HT thermostat 250), ratchet and socket for quick removal and replacement of covers, and a good T&B style crimper ($10-$20 at your local hardware and well worth it even if you only use it a couple of times)

30 minutes and done - the dryer now cranks out the heat and the advanced settings (Auto dry) work great - no more 2-3 times throug to get things dry.

If you have a minimum of mechanical ability and a little bit of electronic troubleshooting skill, you can check and repair this youself and save about an $80-$100 service call.

Thanks to Part Select for the diagram of the dryer layout as well!! (Schematic would be nice if available online, though!)

Shipped the part in about 2 days from order time, as well. Will be back (hopefully not soon, though, as something has to break first!!!)

Be safe and good luck!

(One last note: Make sure your lint trap is clear including the hose - either due to build up or a lazy kid...as this probably caused the failure as heat could not escape...)

One of the drum support rollers was worn out

  • Customer: David from Fleetwood, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 7 of 9 people found this instruction helpful
I lifted the top of the dryer and removed the front panel. I removed the drum exposing the drum rollers. I replaced the rollers and reassembled the dryer. The exploded views on the web site made it easy to see what to do.

Broken dryer belt

  • Customer: Steven from Bridgewater, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 10 people found this instruction helpful
Prop up the hood of the dryer with flat bar. Take out 2 screws holding dryer front end and 2 switch screws for dryer light inside dryer door. Secure dryer drum with bungee cord. Lift front end and remove. Remove broken belt. Route new belt over drum and pass underneatch idler pulley at botttom of dryer. Apply pressure to idler pulley w/one hand while securing belt around motor with the other. Make sure drum seals are snug between front and back of dryer while putting everything back together.
Have confidence. This is a very easy fix.

Dryer motor siezed up, from age and wear

  • Customer: S.K. Mechancil Company from Pittsfield, MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 7 of 10 people found this instruction helpful
Troubleshhot problem, used multimeter to verify current to motor. Once that i was sure motor was getting proper voltage, I used a meg-ohm meter on A/C motor windings and physically tried to turn motor and found that it was siezed. I then cleaned inside of unit inspected belt and drum rollors. Due to the cost of the items, I decided If I was going to replace the motor I should replace all moving parts, and install new belt. Everything went easy. WHAT WAS MOST IMPRESSIVE! was that the Parts people sent the correct parts on time the first time, with no hiddin charges. There web site should accurate diagrams of parts and internals of machine. I was really pleased and will use this service again. Thank you

dryer kept running when door was open

  • Customer: Dean from New Bern, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 7 of 10 people found this instruction helpful
changed out the switch. easy. about 20 minutes. part came quickly (2-3 days). great service. thanks.

Dryer would not start.

  • Customer: Rebecca from Scarsdale, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Unplug dryer from mains. Remove the back of the dryer. Thermal fuse is located on the left hand side near the bottom as you face the back of the dryer. Remove fuse and connect new fuse. Never repaired an appliance before and this was so easy!
All Instructions for the 11062202100
76-90 of 1,270