Models > 11016852501 > Instructions

11016852501 Kenmore Washer - Instructions

All installation instructions for 11016852501 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11016852501
46-60 of 1,037
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer would drain, agitate but not spin and was very noisy and would vibrate heavily

  • Customer: Michael from Schuylkill Haen PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 10 of 11 people found this instruction helpful
I first watched the youTube vidio on yhe PartSelect web site. After getting a visual of the repair, I decided to tackle the job with a better understanding and knew the repair was easy to purform. First I took the two screws out of the contrl panel on top of the washer, rolled the panel back to expose the clips that hold the metal cabinet to the back panel of the washer. After removing the cabinet I was ready to lay the washer on it's back and had a clear view of the pump, motor and clutch... I was able to easly identify these parts because I took time to watch the video. Using a flat head screwdriver I removed the clips that hold the pump to the motor... Without disconnecting the hoses connected to the pump I pushed the pump to the side and out of the way. This further exposed the motor. Using the flat head screwdriver, I removed the clips holding the motor to the transmission (they just snap off like they did on the pump). The motor was now ready to be removed from the transmission ( it just lifts off) before removing it I disconnected the power suply wire from the motor... Now the motor can be completely removed. I identified the drive couupler 1/2 was on the motor shaft the other 1/2 was on the transmission shaft.. On both halfs the splines were broken. I removed the old broken drive coupler. Since I already had the machine so far apart i figured i would replace the clutch also. Using a deep socket ratchet wit an extention I removed the agator... I then unbolted the transmission (only three bolts) I gentely pulled the transmission and shaft out of the bottom of the washer. This exposed the clutc assembly, I removed the clutc ( which wasn't bad or wore by the way) and replaced it.... I figured I had it and I was this far into the repair why not. After relpasingvthe clutch, I slid the shaft and transmission back into place tightened the bolts and that was done. I then slid/replaced the drive coupler... Placing one half on the motor shaft the other on the transmission shaft, placed the rubber bushing on the oneside of the plastic drive coupler. And mounted the motor back on the transmission utilizing the clips I took off earlier. Once the motor was in place I installed the waterpump fastened by the clips. Flipped yhe washer up, replaced the cabinet... Tightened down the the control panel and was ready to do some wash..: the washer runs perfect now and I saved myself about $700.00. It was allot easier than I thought it would be... Watching the youTube video is the secret to success. The washer is running like the day I bought it new... All for only 53.00. Hats off to everyone at PartsSelect for going above and beyond. Regards, ~ Michael

tub off center, rubbing on outer tub in spin

  • Customer: Charles from Rose Bud AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers
  • 9 of 9 people found this instruction helpful
turned the washer on it's back and shoved the tub to the side to release pressure on a spring ,pulled it loose and installed new one. this worked for the back two then turned washer on it;s face and repeted the process on the front spring.
Washer works great now.

Scratches in Surface

  • Customer: Michelle from Richardson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

The support sprint had broke which left the basin unleveled so water would leak behind the basin and onto the floor

  • Customer: Michael from Newark DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 18 people found this instruction helpful
I replaced the broken support spring and the problem was fixed

Agitator was barely agitating. Making a clicking noise.

  • Customer: Charmaine from Slidell LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 9 of 10 people found this instruction helpful
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.

Washmachine wouldn't spindry

  • Customer: Chuck from South Holland IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 9 of 11 people found this instruction helpful
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.

leaking drain pump. Obviously a common problem with this washer

  • Customer: John from Solana Beach CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 8 of 8 people found this instruction helpful
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.

Water was leaking at the pump

  • Customer: Paul from Painesville OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 14 people found this instruction helpful
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.

Agitator moves freely in both directions

  • Customer: James from NAPERVILLE AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 9 of 11 people found this instruction helpful
First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.

I bought a used washer from a friend and they had cut the drain hose short .

  • Customer: Francis from Yuba City CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 10 of 14 people found this instruction helpful
I got a pair of channel lock pliers and took off clamp on the hose, after laying wash machine on it's side, poped off a few little clips and replaced the hose, and now everything works perfect.

top agitator would not operate

  • Customer: Larry from Edgewood TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

water leaking from pump

  • Customer: michael from westmoreland city PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 12 people found this instruction helpful
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.

would not spin properly even with new coupling

  • Customer: david from o AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 10 of 15 people found this instruction helpful
Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towards me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order

water leaking during run cycle

  • Customer: michael from weymouth MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 8 of 10 people found this instruction helpful
flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer

Wash machine, wouldn't spin dry the close. The pump still worked to drain the water.

  • Customer: Matthew from Albany MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 11 of 19 people found this instruction helpful
Unplug power from wall.
Disconnected water lines
Tip Unit on it's side. (Recommend turning so motor is to the top side)
Disconnect Electrical connector and Hoses from the pump and motor.
Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry)
Remove old coupling pieces from transmission/motor(used a long screw driver, rock back and forth)
used air compressor to clean up electric motor
replace new coupling on motor and transmisison (may need hammer to tap into place)
set rubber bushing on transmission side (transmission shaft should be facing up at this point)
replace electric motor into place, making sure to line up bushing and motor mounts.
replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.)
replace electrical connectors and hoses
connect washing machine power and water and test
All Instructions for the 11016852501
46-60 of 1,037